Neato Botvac D75 Troubleshooting

Your Vacuum can't finish its route without having to recharge.

Recalibrating your Botvac's battery can help lengthen time between charges and increase its capacity. Before recalibrating your battery turn off any scheduled cleanings.

To reset the battery:

1. Go to the main Menu on the LCD screen then Support then New Battery.
2. Place your Botvac next on your charging station and fully charge the battery and remove the Botvac.
3. Once the battery is fully charged, press the start button to begin a cleaning cycle.
4. If the Botvac displays" Cleaning Complete" on the screen, press the start button again to begin a new cycle.
5. Repeat cleaning cycles until your Botvac displays the message "My Battery is Low".
6. Place your Botvac on its charging station until the status light shines green.
7. Run your Botvac as usual.

If your battery life does not improve after recalibrating your battery you may need to replace it.

If you have determined that your battery is dead or no longer holding a charge it is time to replace it with a new one. To replace the battery follow this guide Neato Botvac D75 Battery Replacement.

Once the battery has been replaced perform a battery recalibration to ensure you get the most capacity and life out of your new battery.

Your Botvac cannot find its charging station when it is time to charge or after a cleaning cycle has been completed.

To ensure that your Botvac has an easy time finding its charging base it is important to pick an appropriate spot for it. The charging station should have three feet of clear space in front of it and between corners or doors. It is best to place it flat against a wall. It is also important to make the base visible to your Botvac from around the room. Avoid placing the base under furniture or tilted up or down as that may interfere with docking.

If you start a cleaning cycle from anywhere other than the charging base it will find it while cleaning and dock once it completes its cycle. If your Botvac does not see the charging base on its route it will end the cycle where it began it. For this reason we recommend that you start each cleaning cycle from the charging base.

Your robot won't clean during its scheduled cleanings.

Make sure your robot is fully charged. Check the clock. If the clock displays 0:00, then reset the clock.

To reset the clock:

1. Press the button beneath the display to select MENU
2. Choose SET CLOCK
3. Using the up and down arrows, follow the prompts on the screen to set the time and day to the current time and day.

Your robot may have run out of power. Return your robot to its base and allow it fully charge before starting a cleaning cycle.

Return your robot to its base and start the robot from its base.

Like the solution above, return you robot to its base and start the robot from its base.

Your Botvac has a hard time moving through your home while cleaning.

Clear your path.

If the path is clear, and the message won’t be solved by clearing the error, move the robot about 1’/30cm away. For the next cleaning cycle, start from a different starting point, or move the base to a different location.

Make sure wheel wells aren’t blocked with debris. If your Botvac needs new brushes or if you need to remove the brushes to clean them please follow this guide Neato Botvac D75 Brushes Replacement

The laser can not detect boundary markers due to obstacles.

Make sure there is nothing preventing the robot from moving forward (e.g., obstacles, tangled in cords, robot is not flat on floor)

Make sure that the boundary markers are flat on the floor and not blocked or hidden under anything (e.g., thick carpet) for the robot to detect them.

To ensure that the laser is working properly make sure the robot’s laser freely rotates. If laser is dirty use a Q-tip to rotate the laser 5 times to the left and 5 times to the right, making sure NOT to put the Q-tip in either hole.

The robot needs to be reset. Push the battery switch UP to OFF, wait 5 minutes and push DOWN to turn back ON.

Your LCD will not display anything even though the robot is on. This is a common issue and easy to fix.

Try doing a soft reset on the device by:

1. Pressing and holding the Home bottom for 20 seconds. If this doesn't work you with step 2.
2. Try doing a hard reset on the device, which is turning the device OFF for 5 minutes and turning it back on.

If none of these steps work and you are still under your one year warranty we suggest contacting the the customer help for Neato so your warranty does not get voided.

If resetting your device does not restore LDC function and your device is out or warranty you may need to replace it using this guide LCD Replacement Guide.