/
DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Cadastre-se
Login
Junte-se à maior comunidade de reparos do mundo
Peças
GuiasRespostas
Editar
Canon PowerShot SD450 LCD Screen Replacement

Canon PowerShot SD450 LCD Screen Replacement

Pierre Teplitxky

Pierre Teplitxky e 6 outros colaboradores

Última atualização em February 19, 2016

15 - 30 minutos
Moderado

Introdução

Ir para o passo 1

Removing the LCD screen for replacement.

O que você precisa

Ferramentas

  • Phillips #00 Screwdriver
    Phillips #00 Screwdriver
  • Spudger
    Spudger

Exibir mais…

  1. Canon PowerShot SD450 LCD Screen Replacement, Casing: passo 1, imagem 1 %32

    • Remove the battery and SD Card from their slots. Leaving these in could cause the battery to ground and ruin the electronics.

    • Unscrew the six screws on the casing. Two are on the bottom as pictured; two more are on each side of the camera.

    Editar

  2. Canon PowerShot SD450 LCD Screen Replacement: passo 2, imagem 1 %32

    • Pull the lanyard mount off of the camera using a spudger or your fingers.

    Editar

  3. Canon PowerShot SD450 LCD Screen Replacement: passo 3, imagem 1 %32 Canon PowerShot SD450 LCD Screen Replacement: passo 3, imagem 2 %32

    • Find the line that separates the casing into its two halves. Hold each half separately, and gently pull apart.

    • Note that there is a small metal clip holding the two halves together. It might help to press down on the back half (indicated) while pulling upward slightly on the front half.

    Editar

  4. Canon PowerShot SD450 LCD Screen Replacement: passo 4, imagem 1 %32

    • Take hold of the inside of the camera, and gently pull away from the back casing.

    Editar

  6. Canon PowerShot SD450 LCD Screen Replacement: passo 5, imagem 1 %32

    • Remove the square, clear, rubber protector from the front of the logic board. This is not necessary to remove, but can easily fall off and get lost during later steps.

    Editar

  7. Canon PowerShot SD450 LCD Screen Replacement: passo 6, imagem 1 %32

    • When you reassemble the camera, make sure the switch on the casing matches the position of the switch on the camera internals.

    • The black viewfinder padding can easily fall off the casing. Make sure you don't lose it when moving around parts.

    Editar

  8. Canon PowerShot SD450 LCD Screen Replacement, LCD Screen: passo 7, imagem 1 %32 Canon PowerShot SD450 LCD Screen Replacement, LCD Screen: passo 7, imagem 2 %32

    • Pull the retaining clip up with the spudger or your finger and remove the ribbon from the socket.

    Editar

  9. Canon PowerShot SD450 LCD Screen Replacement: passo 8, imagem 1 %32

    • Remove the tripod mount screw.

    • Turn the camera around so that the screen is facing you, and the camera is upright.

    Editar

  10. Canon PowerShot SD450 LCD Screen Replacement: passo 9, imagem 1 %32

    • Remove the screw at the top right of the screen.

    Editar

  11. Canon PowerShot SD450 LCD Screen Replacement: passo 10, imagem 1 %32

    • Lift up the screen to reveal the tripod mount screw.

    Editar

  12. Canon PowerShot SD450 LCD Screen Replacement: passo 11, imagem 1 %32

    • Remove the last screw holding the tripod mount to the case. The LCD ribbon threads under the mount, so upon reinstallation, the ribbon will need to be threaded through before the mount is reattached. Take note of the tripod mount orientation.

    Editar

  13. Canon PowerShot SD450 LCD Screen Replacement: passo 12, imagem 1 %32

    • Pull the back light ribbon from it's socket to remove the LCD completely. There is a little hole you can stick the spudger into to help release the ribbon.

    Editar

    The new screen came without a black light ribbon will it work without it? Canon Powershot sd450

    Mike - Responder

Conclusão

To reassemble your device, follow these instructions in reverse order.

4 outras pessoas executaram este guia.

Autor(a)

com 6 outros contribuidores

Pierre Teplitxky

Membro desde: 04/10/10

152 Reputação

Autoria de 2 guias

Emblemas: 10

+7 outros emblemas

Equipe

Cal Poly, Team 25-85, Amido Spring 2010 Membro de Cal Poly, Team 25-85, Amido Spring 2010

CPSU-AMIDO-S10S25G85

4 Membros

Autoria de 5 guias

3Comentários do guia

Followed the steps and replaced the broken screen. Now I get only a white screen when turning the camera on. It does take pictures but it won't show anything but a little red dotted arrow on the right hand side over the white screen. Do you have a clue of what is happening?

Roberto - Responder

Salve, dove posso acquistare un display?

Germano Tinari - Responder

Salve, sapreste dirmi dove posso acquistare un display?

Germano Tinari - Responder

Comentar

Visualizações:

Últimas 24 horas: 1

Últimos 7 dias: 1

Últimos 30 dias: 19

Ao todo: 6,741