iPad Mini CDMA Logic Board Assembly Replacement

Walter Galan e 3 outros colaboradores

Última atualização em August 15, 2024

Nenhuma estimativa

Moderado

Pré-requisito somente

Este guia destina-se apenas a ser usado como pré-requisito para outros guias. É incompleto por si só.

Introdução

Ir para o passo 1

Prereq for disconnecting all connectors from logic board.

O que você precisa

Ferramentas

Exibir mais…

Passo 1 Logic Board Assembly

iPad Mini CDMA Logic Board Assembly Replacement, Logic Board Assembly: passo 1, imagem 1 %32

iPad Mini CDMA Logic Board Assembly Replacement, Logic Board Assembly: passo 1, imagem 2 %32

Ferramenta utilizada neste passo:

Tweezers

$4.99

Adicionar ao carrinho

Use tweezers to peel up and remove the small piece of tape covering the front-facing camera cable connector.

Editar

Passo 2

The front-facing camera cable connector is secured with pieces of tape that wrap up around the sides of the cable and are fastened to two small metal plates.
Use a plastic opening tool to gently pry the upper metal plate up from the front-facing camera cable connector.
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the front-facing camera cable connector.

Editar

Passo 3

Gently pry the second (lower) metal plate up from the front-facing camera cable connector.
Again, carefully pry the plate up and away from the front-facing camera cable connector.

Editar

Passo 4

Use a plastic opening tool to pry the front-facing camera cable's connector up from its socket on the logic board.

Editar

Passo 5

Gently fold the front-facing camera cable up and out of the way of the logic board.

Editar

Passo 6

Use tweezers to peel up and remove the small piece of tape covering the headphone jack cable connector.

Editar

Passo 7

Use a plastic opening tool to gently pry the lower metal plate up from the headphone jack cable connector.
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the headphone jack cable connector.

Editar

Passo 8

Pry the second (top) metal plate up from the front-facing camera cable connector.
Again, carefully pry the plate up and away from the headphone jack cable connector.

Editar

Passo 9

Use a plastic opening tool to pry the headphone jack cable's connector up out of its socket on the logic board.

Editar

Passo 10

Gently bend the headphone jack cable back, away from the logic board.

Editar

Passo 11

Use a plastic opening tool to pry the top left antenna cable up from its socket on the logic board.

Editar

Passo 12

Remove the following three screws securing the top right antenna to the rear case:
Two 1.3 mm #00 Phillips screws from the side of the antenna's socket.
One 1.8 mm #00 Phillips screw.

Editar

Passo 13

iPad Mini CDMA Logic Board Assembly Replacement: passo 13, imagem 3 %32

Disconnect the top right antenna's coaxial cable from the logic board with a plastic opening tool.
Gently bend the cable and screw tab up out of the way of the logic board.

Editar

Passo 14

Use a plastic opening tool to pry the rear-facing camera cable up from its socket on the logic board.

Editar

Passo 15

Pry the top right antenna's ribbon cable up from its socket on the logic board with a plastic opening tool.

Editar

Passo 16

Use tweezers to peel up and remove the small piece of tape covering the button ribbon cable ZIF connector.

Editar

Passo 17

Use the tip of a spudger to lift up the tab on the button ribbon cable ZIF connector.

Editar

Passo 18

Use tweezers to pull the button ribbon cable straight out of its ZIF socket on the logic board.

Editar

Passo 19

iPad Mini CDMA Logic Board Assembly Replacement: passo 19, imagem 3 %32

Gently peel back the wide piece of tape covering the top of the right speaker.

Editar

Passo 20

iPad Mini CDMA Logic Board Assembly Replacement: passo 20, imagem 3 %32

Continue peeling the tape, and remove it from the iPad.

Editar

Passo 21

iPad Mini CDMA Logic Board Assembly Replacement: passo 21, imagem 3 %32

Use the flat end of a spudger to disconnect the two bottom antenna cable connectors from their sockets on the logic board.

Editar

Passo 22

Use the tip of a spudger to peel back the small piece of tape covering both antenna cables on the bottom right side of the iPad.
Leave the lower part of the tape stuck to the back of the rear case to aid in reassembly.

Editar

Passo 23

With the tip of a spudger, peel up the larger piece of tape covering both antenna cables near the bottom of the rear case.
Do not try to remove this piece of tape; it is wrapped around the top antenna cable.

Editar

Passo 24

iPad Mini CDMA Logic Board Assembly Replacement: passo 24, imagem 3 %32

Use the tip of a spudger to pry the small metal retaining clip off the left antenna cable, then de-route the cable from the clip.

Editar

Passo 25

De-route the antenna cable from the corner of the iPad.

Editar

Passo 26

Use the tip of a spudger to remove the small piece of tape securing the antenna cable in the bottom right corner of the iPad.

Editar

Passo 27

Peel the cable back from the corner of the iPad.

Editar

Passo 28

iPad Mini CDMA Logic Board Assembly Replacement: passo 28, imagem 3 %32

Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.
Gently pull the antenna cable out of the way as you work along the piece of tape, to keep it from resealing.

Editar