Nerf N-Strike Elite Hail-Fire Right Shell Replacement

sage e 3 outros colaboradores

Última atualização em March 17, 2014

20 - 40 minutos

Moderado

Pré-requisitos ausentes

Melhor Introdução

Introdução

Ir para o passo 1

Use this guide to detach the right shell.

O que você precisa

Ferramentas

A iFixit ganha comissão quando você compra por estes links.

Passo 1 Left Shell

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, imagem 1 %32

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, imagem 2 %32

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, imagem 3 %32

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.
Remove the two 9.0 mm Phillips screws securing the battery compartment.
Slide the battery compartment out.

Editar

Passo 2

Remove the five 9.0 mm Phillips screws securing the trigger.

Editar

Passo 3

Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.
Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

Editar

Passo 4

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 4, imagem 3 %32

Remove both halves of the ring by tugging on it upwards until the lock gets freed.
This requires quite a bit of force and if you are not careful, you may break the plastic lock.

Editar

Passo 5

Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

Editar

Passo 6

Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

Editar

Passo 7

Remove the three 9.0 mm Phillips screws holding together the firing chamber.
Remove the single 7.0 mm Phillips screw below the barrel.
Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

Editar

Passo 8

Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

Editar

Passo 9

Remove the two 9.0 mm Phillips screws holding together the handle.
Remove the plastic cover of the handle.

Editar

Passo 10

Insert one plastic opening tool inside one side of the orange part depicted in the picture.
Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

Editar

Passo 11

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 11, imagem 3 %32

Pull one end of the handle away from the orange latch.
Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

Editar

Passo 12

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 12, imagem 3 %32

Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.
Completely remove the left shell from the rest of the Nerf Gun.

Editar

Passo 13 Inner Plastic Components

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, imagem 1 %32

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, imagem 2 %32

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, imagem 3 %32

Remove the cartridge support.

Editar

Passo 14

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 14, imagem 3 %32

Remove the handle crank.

Editar

Passo 15

Remove the clear plastic barrel cover.

Editar

Passo 16

Remove the firing pin.

Editar

Passo 17 Right Shell

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Right Shell: passo 17, imagem 1 %32

Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Right Shell: passo 17, imagem 2 %32

Lift the trigger mechanism out of the shell.
You cannot fully remove the trigger mechanism just yet. However taking it out of the shell helps in later steps.

Editar

Passo 18

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 18, imagem 3 %32

Remove the two 9.0 mm Phillips screws.

Editar

Passo 19

Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 19, imagem 3 %32

To remove the motor and trigger mechanism you have to detach these two wires which are glued to the shell.
Hold close to the wire and pull upward slowly.
If you pull too quickly you can potentially damage the wire.