Conserte seus objetos

Direito de executar reparos

Loja

Canon PowerShot S500 LCD Replacement

Escrito Por: Nathan Balcom (e 6 outros contribuidores)
  • Comentários: 0
  • Favoritos: 1

Dificuldade

Moderado

Passos

16

Tempo necessário

30 minutos

Partes

2

Sinalizadores

0

Introdução

This shows how to replace the LCD.

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

  1. Unscrew five Phillips screws using a #0 Phillips screwdriver. One screw is on upper right corner of the back panel.

    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    Editar

  2. Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    Editar

  3. Remove the rear cover from the rest of the camera.

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    Editar

  4. Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver. Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    • Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    Editar

  5. Free the front cover from the rest of the camera.

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    Editar

  6. Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    Editar

  8. Gently separate the top of LCD from the rest of the camera using your thumb.

    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    Editar

  9. Unscrew single Phillips screw with a #0 Phillips screwdriver. Free the bottom panel and attached ribbon from the rest of the camera.

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    Editar

  10. Turn over the camera.

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    Editar

  11. Place the Spudger between the orange ribbon and the black ribbon gate.

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    Editar

  12. Place the Spudger in the corner of the ribbon above the hole.

    • Place the Spudger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    Editar

  13. Free this ribbon and the bottom panel from the rest of the camera.

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    Editar

  14. Turn the camera over so you can see the LCD.

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    Editar

  15. Lift the blue ribbon gate using the Spudger.

    • Lift the blue ribbon gate using the Spudger.

    Editar

  16. Insert the Spudger into the hole of the ribbon.

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    Editar

  17. Lift the LCD away from the rest of the camera.

    • Lift the LCD away from the rest of the camera.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor

com 6 outros contribuidores

Nathan Balcom

Membro desde: 21/01/2010

81 Reputação

8 Guias de autoria

Emblemas: 9

+6 outros emblemas

Equipe

Cal Poly, Team 16-28, Maness Winter 2010 Membro de Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 Membros

8 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Duração total: 2,934