Ir para o conteúdo principal
Boosted Board 1st Generation Pulley Bearings Replacement

Boosted Board 1st Generation Pulley Bearings Replacement

Emily Imfeld

Emily Imfeld e 4 outros colaboradores

Última atualização em November 30, 2016

Nenhuma estimativa
Moderada
Guia do aluno destaque

Good bearings are essential for smooth ride. This guide will help you take out and replace the pulley bearings on the rear wheels of your Boosted Board. You can choose to replace the bearings with new ones, or just clean the existing bearings.

O que você precisa

A iFixit ganha comissão quando você compra por estes links.
  1. Boosted Board 1st Generation Pulley Bearings Replacement, Rear Wheels: passo 1, imagem 1 %32 Boosted Board 1st Generation Pulley Bearings Replacement, Rear Wheels: passo 1, imagem 2 %32
    • Loosen the two 16.74 mm motor mount hex nut screws with a 9/64" Allen wrench.

    • Do Not Remove the Screws.

  2. Boosted Board 1st Generation Pulley Bearings Replacement: passo 2, imagem 1 %32
    • Compress the motor mount back towards the wheel.

    • While keeping the motor mount compressed, tighten one of the hex nuts that you loosened in the previous step.

    • The motor mounts are spring tensioned so it is necessary compress them to loosen the belts.

  3. Boosted Board 1st Generation Pulley Bearings Replacement: passo 3, imagem 1 %32 Boosted Board 1st Generation Pulley Bearings Replacement: passo 3, imagem 2 %32
    • Remove the axel nut with a 1/2" socket wrench

  4. Boosted Board 1st Generation Pulley Bearings Replacement: passo 4, imagem 1 %32 Boosted Board 1st Generation Pulley Bearings Replacement: passo 4, imagem 2 %32 Boosted Board 1st Generation Pulley Bearings Replacement: passo 4, imagem 3 %32
    • Rotate and pull counterclockwise until the wheel comes off the axle completely.

    • The front washer will come off with the wheel.

    • Remove the back washer from the axle.

    • Replacing the wheel requires the bearings to be switched into the new wheel.

  5. Boosted Board 1st Generation Pulley Bearings Replacement, Pulley Bearings: passo 5, imagem 1 %32 Boosted Board 1st Generation Pulley Bearings Replacement, Pulley Bearings: passo 5, imagem 2 %32
    • Use one finger to pull out the pulley bearing.

    • A good technique is to go around in a circle and lift from underneath the bearing in a carving motion.

  6. Boosted Board 1st Generation Pulley Bearings Replacement: passo 6, imagem 1 %32 Boosted Board 1st Generation Pulley Bearings Replacement: passo 6, imagem 2 %32 Boosted Board 1st Generation Pulley Bearings Replacement: passo 6, imagem 3 %32
    • Place the new pulley bearing inside the gear hole and use two fingers to push down evenly until it slides into place.

    • The bearing should be flush with the gear

Conclusão

To reassemble your device, follow these instructions in reverse order.

Emily Imfeld

Membro desde: 10/06/16

532 Reputação

Autoria de 4 guias

Equipe

Cal Poly, Team 15-7, Livingston Fall 2016 Membro de Cal Poly, Team 15-7, Livingston Fall 2016

CPSU-LIVINGSTON-F16S15G7

Membros da 4

Autoria de 6 guias

Um comentário

you mentioned cleaning bearings how do you go about that? (if rep[lacing not an option at moment) Also I noticed a single Large Bearing in my replacement kit, what is that and where do I replace it as I don’t see where it could be (I have a first Gen)

Rick Gram - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 5

Duração total: 1,661