Introdução

Use this guide to replace the motherboard in your Huawei P10 Lite smartphone.

Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive. If the adhesive is hard to cut, use an iOpener to loosen it. If the adhesive is hard to cut, use an iOpener to loosen it.
  • Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.

Adicionar comentário

After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone. Flip the rear cover over to the right side of the phone. Flip the rear cover over to the right side of the phone.
  • After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.

  • Flip the rear cover over to the right side of the phone.

Adicionar comentário

Use tweezers to remove the liquid indicator sticker. Remove the two Phillips #00 screws.
  • Use tweezers to remove the liquid indicator sticker.

  • Remove the two Phillips #00 screws.

  • Remove the four 0,1 inch Phillips #00 screws.

Adicionar comentário

Use tweezers to remove the mainboard shield. Use the flat end of a spudger to disconnect the finger print sensor flex cable.
  • Use tweezers to remove the mainboard shield.

  • Use the flat end of a spudger to disconnect the finger print sensor flex cable.

    • When reassembling apply new adhesive where it is necessary.

Adicionar comentário

Remove the SIM card tray before you perform any further actions.. Remove the SIM card tray before you perform any further actions..
  • Remove the SIM card tray before you perform any further actions..

Adicionar comentário

Remove the three Phillips #000 screws. Use tweezers to remove the two metal shields which cover the flex cables on the mainboard. Use tweezers to remove the two metal shields which cover the flex cables on the mainboard.
  • Remove the three Phillips #000 screws.

  • Use tweezers to remove the two metal shields which cover the flex cables on the mainboard.

Adicionar comentário

Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable. Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable. Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable.
  • Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable.

Adicionar comentário

Disconnect the battery flex cable with a spudger. Unplug the antenna cable with tweezers.
  • Disconnect the battery flex cable with a spudger.

  • Unplug the antenna cable with tweezers.

Adicionar comentário

Disconnect the headphone jack flex cable with the flat end of a spudger. Use an opening pick to pry out the motherboard until you can get a good grip. Both camera are still attached to the motherboard. Don't damage them while you remove it.
  • Disconnect the headphone jack flex cable with the flat end of a spudger.

  • Use an opening pick to pry out the motherboard until you can get a good grip.

  • Both camera are still attached to the motherboard. Don't damage them while you remove it.

  • Remove the motherboard.

    • If you want to replace your motherboard you need to disconnect both cameras and transfer them to your spare part.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Uma outra pessoa concluiu este guia.

Dominik Schnabelrauch

Member since: 23-11-2016

14.040 reputação

256 Guides authored

Equipe

iFixit Membro de iFixit

Community

113 Membros

6.002 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 15

Últimos 7 dias: 83

Últimos 30 dias: 358

Todo: 1,313