Bootloop after housing and screen replacement

Question

iPhone 8

Lançado em 22 de setembro de 2017. Modelo A1863, A1905. Disponível com GSM ou CDMA / 64 ou 256 GB / Dourado, Prateado e Cinza Espacial.

20 Perguntas Visualizar todos | Peças para 46 Loja

Nathan Bolam @bolamn

Rep: 83

3

Postado: 10 de ago de 2019

Opções

Bootloop after housing and screen replacement

Hey All,

Did a housing and screen replacement and now stuck in a bootloop, if i put the phone into recovery mode im able to restore the firmware successfully but then when it restarts it goes straight back to bootlooping.

ive tried disconnecting the front flex with the sensor also reseating all the flex cables but still bootloops, any suggestions as to what parts i should try reordering/replacing

thanks in advanced.

Respondido! Ver a resposta Também tenho esse problema

Esta é uma boa pergunta?

Sim Não

Pontuação 0

Adicionar um comentário

1 resposta

Solução escolhida

Minho @refectio

Rep: 221,8 mil

15

296

808

Postado: 11 de ago de 2019

Opções

Did you transfer over all of the flexes or were they pre-installed in the replacement housing? Either way, you have a ton of variables here and you will need to isolate things one by one.

I would start by connecting the screen (just the screen, no FCAM), Lightning Port (from the original housing as it was a known-good part) and battery and then connect to an iTunes enabled computer. Does it boot properly and remain stable, if so, then add flexes one at a time until the phone fails. If not, then try another charge port or remove the screen to see if it stabilizes. Take notes along the way as this could get confusing.

This will help you determine if this is logic board related or simply a bad flex.

Esta resposta foi útil?

Sim Não

Pontuação 3

5 comentários:

All the flex cables were replaced, unfortunately the original charge flex was damaged thou as it is able to complete a recovery (charges and transfers data) until it restarts i would think it would rule that out?

11 de ago de 2019 por Nathan Bolam

I would still try another charge port.

12 de ago de 2019 por Minho

i left it forr a few days due to work commitments and came back to it sitting on the "Hello" activation screen, after activation and a standard reboot it went back to boot looping.

ill leave it for a few more days and cant see if it goes to the home screen by chance and maybe then i can use xcodes devices and simulators to check the devices console logs.

dunno if this helps any just thought id update.

14 de ago de 2019 por Nathan Bolam

charge flex may be the problem after all, will order a replacement and see how that goes

"panicString" : "panic(cpu 5 caller 0xfffffff01a72805c): \"i2c1::_checkBusStatus SCL is stuck low; last read status 00010108 int shadow 00010100 xfer 00000000 fifo 00000000 for device mic-temp-sens2\"@\/BuildRoot\/Library\/Caches\/com.apple.xbs\/Sources\/AppleS5L8940X\/AppleS5L8940X-166.200.1\/AppleS5L8940XI2C.cpp:340"

16 de ago de 2019 por Nathan Bolam

Okay found the definite cause which was the Power Button Flex Cable, disconnected it then plugged a usb cable in to turn the phone on and worked straight away.

odd one thou as all the buttons/silence switch works :shrug:

16 de ago de 2019 por Nathan Bolam

Adicionar um comentário

All the flex cables were replaced, unfortunately the original charge flex was damaged thou as it is able to complete a recovery (charges and transfers data) until it restarts i would think it would rule that out? — Nathan Bolam
i left it forr a few days due to work commitments and came back to it sitting on the "Hello" activation screen, after activation and a standard reboot it went back to boot looping.

ill leave it for a few more days and cant see if it goes to the home screen by chance and maybe then i can use xcodes devices and simulators to check the devices console logs.

dunno if this helps any just thought id update. — Nathan Bolam
charge flex may be the problem after all, will order a replacement and see how that goes

"panicString" : "panic(cpu 5 caller 0xfffffff01a72805c): \"i2c1::_checkBusStatus SCL is stuck low; last read status 00010108 int shadow 00010100 xfer 00000000 fifo 00000000 for device mic-temp-sens2\"@\/BuildRoot\/Library\/Caches\/com.apple.xbs\/Sources\/AppleS5L8940X\/AppleS5L8940X-166.200.1\/AppleS5L8940XI2C.cpp:340" — Nathan Bolam
Okay found the definite cause which was the Power Button Flex Cable, disconnected it then plugged a usb cable in to turn the phone on and worked straight away.

odd one thou as all the buttons/silence switch works :shrug: — Nathan Bolam

iPhone 8

Bootloop after housing and screen replacement

1 resposta

Adicionar a sua resposta