Ferramentas utilizadas neste teardown

Introdução

Here you will see a breakdown of the Apple Studio Display M2454. This will be useful in repairing broken or malfunctioning parts in the future.

This teardown is not a repair guide. To repair your Apple Studio Display M2454, use our service manual.

Notice that the main components of the monitor are only accessible from the back of the device.
  • Notice that the main components of the monitor are only accessible from the back of the device.

Adicionar comentário

Locate the four hex head screws located on the corners of the back panel.
  • Locate the four hex head screws located on the corners of the back panel.

    • Remove the screws with a 2mm hex screwdriver.

Adicionar comentário

Remove the clear and gray back panels.
  • Remove the clear and gray back panels.

Adicionar comentário

Remove the three screws with #2 phillips head screwdriver.
  • Remove the three screws with #2 phillips head screwdriver.

Adicionar comentário

To remove the metal panel, push towards the bottom of the monitor to release its clips and pull the panel away.
  • To remove the metal panel, push towards the bottom of the monitor to release its clips and pull the panel away.

Adicionar comentário

Remove screw holding the plastic bracket with #2 Phillips head screwdriver.
  • Remove screw holding the plastic bracket with #2 Phillips head screwdriver.

Adicionar comentário

Remove the four screws on the metal bracket.
  • Remove the four screws on the metal bracket.

Adicionar comentário

Remove the two philips head hold-down screws with the #2 Phillips head screwdriver.
  • Remove the two philips head hold-down screws with the #2 Phillips head screwdriver.

Adicionar comentário

Remove black connector by pushing the end of the tab closest to the wiring and pulling away from board.
  • Remove black connector by pushing the end of the tab closest to the wiring and pulling away from board.

Adicionar comentário

Remove white connector by lifting tab and pulling away from board.
  • Remove white connector by lifting tab and pulling away from board.

    • Be careful when lifting tabs, they break easily.

Adicionar comentário

Remove connector connected to the hold down previously removed simply by pulling with hand.
  • Remove connector connected to the hold down previously removed simply by pulling with hand.

Adicionar comentário

Now that the main computer cable is detached, remove it away from monitor.
  • Now that the main computer cable is detached, remove it away from monitor.

Adicionar comentário

Remove the two screws holding the USB port in place with #2 Phillip's head screwdriver.
  • Remove the two screws holding the USB port in place with #2 Phillip's head screwdriver.

Adicionar comentário

Remove the screw on the wire hold down with #2 Phillips head screwdriver.
  • Remove the screw on the wire hold down with #2 Phillips head screwdriver.

Adicionar comentário

Remove white connector connected to LCD main board by lifting tab with tool and pulling away from board.
  • Remove white connector connected to LCD main board by lifting tab with tool and pulling away from board.

Adicionar comentário

The USB port is now detached, remove it from monitor.
  • The USB port is now detached, remove it from monitor.

Adicionar comentário

Remove connector on the left bottom corner of the LCD main board by simply pulling with hand.
  • Remove connector on the left bottom corner of the LCD main board by simply pulling with hand.

Adicionar comentário

Remove the connector on the bottom right corner by 1st removing tape first and pulling with hand.
  • Remove the connector on the bottom right corner by 1st removing tape first and pulling with hand.

Adicionar comentário

Remove top right connector of the LCD main board by pulling with hand.
  • Remove top right connector of the LCD main board by pulling with hand.

Adicionar comentário

Remove the final connector of the LCD main board by pulling with hand.
  • Remove the final connector of the LCD main board by pulling with hand.

Adicionar comentário

Remove the four screws on each corner of the main board with #2 Phillips head screwdriver.
  • Remove the four screws on each corner of the main board with #2 Phillips head screwdriver.

Adicionar comentário

The board is now detached, remove it from monitor.
  • The board is now detached, remove it from monitor.

Adicionar comentário

Locate the top and bottom connector on the CCFL inverter and remove it by inserting pin into the small holes and pulling away.
  • Locate the top and bottom connector on the CCFL inverter and remove it by inserting pin into the small holes and pulling away.

    • This step may be easier with two people.

Adicionar comentário

Remove the two screws on the top and bottom of the CCFL inverter with #2 Phillips head screwdriver.
  • Remove the two screws on the top and bottom of the CCFL inverter with #2 Phillips head screwdriver.

Adicionar comentário

The CCFL inverter is now detached, remove it from monitor.
  • The CCFL inverter is now detached, remove it from monitor.

Adicionar comentário

You have now successfully taken apart a Apple Studio Display M2454.
  • You have now successfully taken apart a Apple Studio Display M2454.

Adicionar comentário

Dylan Perry

Member since: 20-01-2010

129 reputação

5 Guides authored

Equipe

Cal Poly, Team 13-27, Maness Winter 2010 Membro de Cal Poly, Team 13-27, Maness Winter 2010

CPSU-MANESS-W10S13G27

4 Membros

5 Guides authored

This model is also known as the Apple Studio Display 15" LCD.

analogcd - Responder

excellent wee guide......i came here in my search for a replacement stand for this model.

bobby nailen - Responder

Failing caps were the main problem with this — no air flow.

Mal - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 5

Últimos 7 dias: 8

Últimos 30 dias: 16

Todo: 5,969