Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
-
-
Encha uma panela ou frigideira com água suficiente para submergir completamente um iOpener.
-
Aqueça a água até ferver. Desligue o fogo.
-
Coloque um iOpener na água quente por 2 a 3 minutos. Certifique-se de que o iOpener esteja totalmente submerso na água.
-
Use um pegador para retirar o iOpener aquecido da água quente.
-
Seque bem o iOpener com uma toalha.
-
Sua bolsa térmica iOpener está pronta para o uso! Se precisar reaquecer o iOpener, aqueça a água até ferver, desligue o fogo e coloque o iOpener na água por 2 a 3 minutos.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Handling it by the tag, place the heated iOpener on the side of the iPad to the left of the home button assembly.
-
Let the iOpener sit for at least a minute to soften the adhesive beneath the glass.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
As you follow the directions, take special care to avoid prying in the following areas:
-
Front-facing camera
-
Antennas
-
Display cables
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
Ferramenta utilizada nesse passo:Anti-Clamp$24.95-
Pull the blue handle backwards to unlock the Anti-Clamp's arms.
-
Place an object under your iPad so it rests level between the suction cups.
-
Position the suction cups near the middle of the left edge—one on the top, and one on the bottom.
-
Hold the bottom of the Anti-Clamp steady and firmly press down on the top cup to apply suction.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the blue handle forward to lock the arms.
-
Turn the handle clockwise 360 degrees or until the cups start to stretch.
-
Make sure the suction cups remain aligned with each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Wait one minute to give the adhesive a chance to release and present an opening gap.
-
If your screen isn't getting hot enough, you can use a hair dryer to heat along the left edge of the iPad.
-
Insert an opening pick under the screen when the Anti-Clamp creates a large enough gap.
-
Skip the next two steps.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully place a suction cup halfway up the heated side.
-
Be sure the cup is completely flat on the screen to get a tight seal.
-
While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place an opening pick in the gap opened by the suction cup.
-
Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
-
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Continue moving the opening pick down the side of the display to release the adhesive.
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Take the first pick you inserted and slide it up toward the top corner of the iPad.
-
If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out just a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the opening pick around the top left corner of the iPad to separate the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the opening pick in the iPad slightly past the front-facing camera.
-
Take a second pick and insert it to the left of the camera, and then slide it to the corner of the iPad to finish cutting the adhesive on that edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
-
Reheat the iOpener and place it on the remaining side of the iPad—along the volume and lock buttons.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the opening pick around the top right corner of the iPad, releasing the adhesive there.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the opening picks in place, and set the reheated iOpener on the home button end of the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the lower left pick to the lower left corner to cut the adhesive on that corner.
-
Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.
-
The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
With a new pick, slice gently over the left-hand antenna, stopping before the home button.
-
Leave the pick in place before moving on.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Take a new pick and slip it in to the right of the previous pick.
-
Slide across the home button and right-hand antenna using only the very tip to remove the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
With the adhesive loosened, you can now insert the pick near the right-hand corner. Slide the pick to the left, and stop just short of the Home button.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Reheat and reapply the iOpener to the volume control side of the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
On the side of the iPad opposite the volume controls, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along the display cable edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift slowly and gently to further detach the adhesive along the display cable edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
While supporting the front panel glass, use an opening pick to cut the last of the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Once all of the adhesive has been separated, open the glass panel like a page in a book and rest it on your workspace.
-
Cancelar: não concluí este guia.
3 outras pessoas executaram este guia.