Participe da comunidade de reparos - Criar conta

Introdução

Common causes of a faulty mouse button are frequent use, clicking too hard, and dust getting into the switches. The purpose of this guide is to detail how to replace the switches on your Logitech M100 Mouse with the goal of prolonging the life of your mouse.

This guide does not require specialized knowledge except a basic understanding of a soldering iron. Soldering material is metal with a low melting point. Be cautious of the iron and solder's heat when replacing the mouse clicker, as it very hot and can burn skin. It's also important to work in a well ventilated area as the solder can emit fumes that are not good to breath. For more information about soldering, take a look at the How to Solder and Desolder Connections guide.

O que você precisa

1. Passo 1 Switches
  Disconnect the mouse from any devices before attempting to remove any parts or starting the repair.
  
  Flip your mouse over so the bottom is facing up.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
2. Passo 2
  Use a small Phillips #00 screwdriver to remove the single screw at the bottom of the mouse.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
3. Passo 3
  Turn your mouse over so it is facing right side up.
  
  Use a spudger or your hands to carefully separate the top from the bottom housing.
  
  It's important to remove the top housing while leaving the bottom in place, as the scroll wheel and other internal components may fall out otherwise.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
4. Passo 4
  Remove the external cable from the slot at the front of the mouse.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
6. Passo 5
  Remove the circuit board from the mouse by pushing down at the back and lifting up at the front.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
7. Passo 6
  Lift the scroll wheel from the board.
  
  There should be a total of four parts that make up the scroll wheel.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
8. Passo 7
  Pull the USB cable away from the connector in the same direction as the individual wires to remove it from the motherboard.
  
  This step may prove difficult with just your hands. Use a spudger if you need to.
  
  Pull evenly on the full width of the cable so that no individual wires are overly strained.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
9. Passo 8
  Find a suitable method to hold the circuit board in place so you don't have to hold it in your hands.
  
  Use a small vice to keep it in place or helping hands for this next step.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
10. Passo 9
  Use a soldering iron to heat the solder points securing both switches, and remove the switches using tweezers.
  
  The soldering iron and the solder holding the switch in place will be very hot and can burn you.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
11. Passo 10
  Replace each switch and solder it to the circuit board.
  
  The soldering wire may conduct heat up to the hand holding it.
  
  Be sure to work in a well ventilated space as the solder may emit smoke.
  
  You can use tape to hold the switch in place while soldering.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
12. Passo 11
  Reassemble the mouse by following steps 2-7 in reverse order.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024