Model A1181: 1.83, 2, 2.1, 2.13, 2.16, 2.2, or 2.4 GHz Core 2 Duo processor

1438 Perguntas Ver todas

Ethernet cable does not snap in the jack

When I plug an ethernet cable into the jack, it will go in but the little tab will not lock into place. What is the problem?

Respondido! View the answer Também tenho esse problema

Esta é uma boa pergunta?

Pontuação 0

Comentários:

have you checked the plug?

does it happen with more than one?

por

Yes, its all clear and its happens every time. even with different cables

por

The "top" of the macbook jack is not tall enough at the outer (opposite the contacts) end. So, the latching tab can be slightly depressed downward by the aluminum, causing the essential hook on the plug to not fully mate with the hook in the jack. The solution is to file down the top side of the latch until the keeper will engage as expected. A more drastic method that would work with all cables would be to remove a notch of aluminum from the top of the case. Ugly, but effective.

por

Adicionar um comentário
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12
Spread Fixmas Cheer
Get $12 off your purchase of $50 or more with code FIXMAS12

5 Soluções

Solução escolhida

A question for your question... Has your port exhibited this behaviour since new, or is this a recent development?

**Edit**

Since this problem started after you purchased the machine, it was most likely caused by something getting into the port, or by a physical deformity of the case or connector housing itself. If you can't see anything stuck inside the port, look to see if it is bent/broken anywhere around the edge (mainly right at the top where the cable's clip connects).

If cables aren't fitting into the port anymore, my workaround would be to make sure you have a cable with lots of slack, and remove the clip that holds it in place. Generally if there is no tension, an ethernet cable will stay in the port without the clip.

Esta resposta foi útil?

Pontuação 1

Comentários:

I've had it since 2006 and i think it was working good then, I can't remember when it started but it is not recent - maybe 1 or 2 years ago.

por

Adicionar um comentário
Resposta Mais Útil

Hi! Sometimes I've found that the little plastic tab on the top of the connector goes "soft" and does not have enough bounce to get high enough to latch inside the port. If you carefully pull that plastic strip upward, making sure not to break it off, this can re-establish its position so that hopefully when you plug it in again, it will rest in the proper position to click inside the port. Of course, if you've tried multiple cables with the same result, it may not be this at all and may be something inside the port.

Esta resposta foi útil?

Pontuação 1

Comentários:

No, its definitely the jack as I have been using brand new cables.

por

Adicionar um comentário

Plug may be deformed around, or have something in, the recess for the tang.

N.

Esta resposta foi útil?

Pontuação 0

Comentários:

To me, It looks perfectly normal..

por

Adicionar um comentário

Might want to check the metal wire contacts inside the jack to make sure each one is in its proper channel. I know with a phone jack, I've had those metal contacts get bent and keep the phone plug from going in properly.

Esta resposta foi útil?

Pontuação 0
Adicionar um comentário

It happens with me too. It's just unproperly shaped cable or port. Seeing that you're getting the same problem with different cables, it indicates a problem in your jack's shape.

Try inserting modeling clay in the port and comparing the shape that comes out with the shape of the connector. Then maybe you could remove the excess part.

Esta resposta foi útil?

Pontuação 0

Comentários:

That seem kinda dangerous dont you think..

por

Adicionar um comentário

Adicionar a sua resposta

AussieMac será eternamente grato(a).
Visualizar Estatísticas:

Últimas 24 horas: 11

Últimos 7 dias: 65

Últimos 30 dias: 269

Todo: 14,669