JBL FLIP 3

Question

Repair and support for the third generation of the Flip portable speaker by JBL.

70 Perguntas Visualizar todos

XxMasked ManxX @xxmaskedmanxx

Rep: 23

2

1

Postado: 22 de out de 2017

Opções

JBL FLIP 3 - Piece of motherboard fell off labelled 1R5

I dropped by speaker a little while ago, it approximately fell from 1.4 meters, as soon as it dropped the audio stopped, I checked it, the battery charges, it connects to Bluetooth and the led display works, so I further investigated because I could here a rattle, I have check the motherboard and found a piece that looks like it has been de attached from the motherboard labelled 1R5? Is this fixable?

Respondido! Ver a resposta Também tenho esse problema

Esta é uma boa pergunta?

Sim Não

Pontuação 1

6 comentários

Help required please

23 de out de 2017 por XxMasked ManxX

where is it placed on the mother board?

6 de mar de 2018 por LunarYTS

Hi, I have the same problem but when I put the inductor in its place and turn on the speaker it really heats up and even releases smoke. Any help with that?

29 de jun de 2019 por Fernando Ramonborja

Hey guys I wanted to ask how do I attach this price onto the motherboard I have the same problem the “1R5” piece

6 de jan de 2020 por champs49ers

Where can I get a replacement part for the broken 1R5 part?

2 de ago de 2020 por Daniel Sepulveda

Exibir mais 1 comentário

Adicionar um comentário

1 resposta

Solução escolhida

daniel @tech_ni

Rep: 34,4 mil

10

22

44

Postado: 23 de out de 2017

Opções

yes its fixable its a coil, you need to find the place it came of on the board and solder it on, but you would need to see if the pads have been damaged

Esta resposta foi útil?

Sim Não

Pontuação 5

4 comentários:

Thanks for your help, I had got impatient so I decided to play around and found where it went and the sound worked so I soldered it back on and there we go done.

23 de out de 2017 por XxMasked ManxX

Hello my name is David I have the same problem you describe ! I would like to ask for an explanation about how to solder it back , i don't know how to do it or to verify if the pads are damaged

Please help me

Thank you and advance

31 de jan de 2018 por David Mencias

Check to make sure the pads are shiny metal. If they are dull green material, the pads are damaged. If they are metal, they are good.

Due to how JBL assembles this speaker, dont bother taking the board out. Just remove the front speakers (carefully using a screwdriver to disconnect the connector) and the side diaphrams. Tin the pads and the 1R5 part (called an inductor), then remove the excess solder with a wick. Use a chisel tip soldering iron to solder one side at a time, being careful not to melt the case. Hold it for like 15-30 seconds on each joint so you get a good connection: the reason it failed in the first place was that JBL had cold solder joints.

15 de mai de 2018 por Ella Jameson

does anyone know how to test the coil or even replace it. I checked ebay cant find any .

31 de ago de 2018 por migel anguiano

Adicionar um comentário

Hi, I have the same problem but when I put the inductor in its place and turn on the speaker it really heats up and even releases smoke. Any help with that? — Fernando Ramonborja
Hey guys I wanted to ask how do I attach this price onto the motherboard I have the same problem the “1R5” piece — champs49ers
Thanks for your help, I had got impatient so I decided to play around and found where it went and the sound worked so I soldered it back on and there we go done. — XxMasked ManxX
Hello my name is David I have the same problem you describe ! I would like to ask for an explanation about how to solder it back , i don't know how to do it or to verify if the pads are damaged

Please help me

Thank you and advance — David Mencias
Check to make sure the pads are shiny metal. If they are dull green material, the pads are damaged. If they are metal, they are good.

Due to how JBL assembles this speaker, dont bother taking the board out. Just remove the front speakers (carefully using a screwdriver to disconnect the connector) and the side diaphrams. Tin the pads and the 1R5 part (called an inductor), then remove the excess solder with a wick. Use a chisel tip soldering iron to solder one side at a time, being careful not to melt the case. Hold it for like 15-30 seconds on each joint so you get a good connection: the reason it failed in the first place was that JBL had cold solder joints. — Ella Jameson
does anyone know how to test the coil or even replace it. I checked ebay cant find any . — migel anguiano

JBL Flip 3

JBL FLIP 3 - Piece of motherboard fell off labelled 1R5

1 resposta

Adicionar a sua resposta