daniel

@tech_ni

daniel

8.251	Reputação
610	Soluções
0	Guias
Membro desde 06-08-2017

Votos

Perguntas

Stuck at apple logo 19-12-2019
After lcd fpc replacement phone booted fine. Now stuck on apple logo and power supply showing 0.33 amps when button is...
Red light a beep 07-05-2019
Has anyone found a fix for ghd platinum red light and beep yet
Need schematics urgently please 03-04-2019
This laptop won't turn on after a power cut. When the charger is plugged in the power brick light goes out. I felt a...
not charging and taking along time to boot to home screen 18-01-2019
@refectio i have an issue with this iphone 6. when i got it, it wouldnt boot. on dc and charger with battery disconnected...
no power even after both power ics changed 24-08-2018
so i have an s6 edge+ no power, replaced both power ic’s. getting around 3.5v in both locations but not turning on and no...
vdd main short but no heat 14-07-2018
so i have an iphone 7 in this morning and as title says i have a vdd main short, wire soldered on and drawing 2 amps but...
dim backlight after liquid damage 24-05-2018
i have a macbook air 820-3437 which was liquid damaged, doa. corrosion was around smc and u7700, reballed smc and it...
about gsx account not phone 23-05-2018
does anyone have an apple gsx account that can help me figure out how to get an account
will only boot to safe mode 22-04-2018
i have a ps4 that wont boot when the power button is pressed just blue pulsing light, yet it will boot into safe mode and...
iPhone 6 not booting 19-04-2018
im having an issue with an iphone 6, when i got it, it was bootlooping, now i have replaced pmic, tristar and tigris. but...

Página 1 de 4

Avançar

Respostas

Resposta para "Freezer machine LCD separation? Does it worth?" 1 semana atrásabril 3, 2020
Most people I have seen on a screen refurb page on facebook just use heat and wire for most screens.
Resposta para "iPhone technically charging(usb amp meter), but wont turn on!" 1 semana atrásabril 3, 2020
Have you connected it to iTunes to check if its recognised.
Resposta para "Black screen after replacement" 1 semana atrásabril 3, 2020
It could just be a bad screen, it happens.
Resposta para "Is Galaxy s10 plus replacement screen waterproof?" 1 semana atrásabril 3, 2020
No phone is 100% waterproof to begin with. If you want to change the screen and frame buy a samsung service pack as it will be the same as factory.
Resposta para "PSU connector ripped from motherboard" 15-01-2020
Scrape the vias until you see copper. Where the bottom 2 arrows point. The other pad is there and the 1 with no via is probably ground so can be jumped from the ground side of the capacitor. Use epoxy to attach the connector then solder wires from the vias to the connector pins. Once done add some more epoxy for strength.
Resposta para "iPhone stuck in boot loop after Apple logo replacement" 12-01-2020
Ok if you were adding an led apple logo, then smelt burning and stopped. How did you eventually add it.
Resposta para "iPhone XR Boot loop after water damage" 09-01-2020
Have you tried it with just the lcd connected, no cameras etc. Could also be a screen issue. Remember the logic board is 2 seperate pcbs soldered together and you would only see damage when they are seperate.
Resposta para "Why does my ipad not work after digitizer,LCD and battery replacement?" 03-01-2020
Check for pry damage around the connectors. Also download 3utool, connect the ipad and see if it detects it as you can use this to kick it out of recovery mode.
Resposta para "MacBook Pro No backlight" 03-01-2020
Change the fuse. You shouldn't just get voltage on 1 side.
Resposta para "Missing resistor near charging port" 24-12-2019
There is no photo attached.

Página 1 de 61

Avançar

Reputação ao longo do tempo

Discriminação da reputação

Evento	Contagem	Delta
Voto à favor da postagem	454	5420
Resposta aprovada	108	3240
Resposta Aceita	4	40
Votou negativo para o post	1	-2
Voto contra à postagem	8	-48
Seu comentário foi apagado por ter sido marcado como inapropriado	4	-400