Este usuário ainda não preencheu o perfil.
Guias concluídos
Perguntas
I need to clean my keyboard, so remove keycaps. Despite I act very gently, and tried different technics (prying from the...
Saiba maisI’ve got Sony with a power problem. After investigation I found it has an essential chip (IC5700) killed by a dummy...
Saiba maisHi I need a Full HD screen replacement for my DV6-7000 machine. Service guide says it has part number 682090-001 but it...
Saiba maisI’ve got weird think. One say I wiped the screen with a soft microfiber. No problems was expected, but later I found I...
Saiba maisNOTE: I posted this thread on the Apple forum. A minute later it has been wiped out. Coincidence? I don’t think so… I...
Saiba maisI’ve got A1398 Late 2013 with 2.6ghz i7-4960HQ. Thermal paste apparently wasn’t swapped it’s entire life. In Cinebench it...
Saiba maisHi! I just got MBP and immediately noticed thin horizontal lines all over the screen, most notable on the white...
Saiba maisThere’s a lot of debates on that topic. But no clear answer Apple Genuine chargers are made by major power supply...
Saiba maisWeird thing. After I slightly droped my iPad (on it’s back) I started noticing unpleasant behaviour - a vertical “strip”...
Saiba maisGuys, I just swapped lightning flex cable im my iPad mini 1. It was tricky, but I somehow succeed, except one speaker is...
Saiba maisPágina 1 de 2
Respostas
А если заменить аккум на старый? Но вообще, по симптомам похоже что что-то накрылось. Самое худшее - если smc...
Saiba maisЕсли кратко - нет. Если подробнее: шлейфы, идущие на экран, запаянны между слоями платы-драйвера. Их не отпаять. От экрана - тоже не отпаять, это мероприятие для спецлаборатории, только какие-то редкие китайцы такое умеют. Если вы в принципе хотите заняться таким ремонтом, вам нужно будет подходить радикально иначе - пересадить чипы и детальки с одной платы на другую. И очень ответственно документировать процесс - никаких схем в доступе нет. Понадобится неплохой скилл пайки феном! И, конечно, очень аккуратно обращаться с платой и шлейфами, малейшее повреждение и всё. И защитить матрицу от тепла
Saiba maisDid you solve the problem?
Saiba maisIt may be easy to be confused what is the cause, but as the screen seems intact and it happened when you tilted the screen I think it’s more likely to be a flex cable problem. It’s not expensive - try it first. But be VERY careful inside, the clip connector is fragile. Tackle it with a toothpick. And beware FLASH DISCHARGE PADS. Touching them is a little trick to momentarely waste a few hundred bucks killing your camera as I did once. Better never get there.
Saiba maisI’ve got almost the same question but slightly different. I need to fit 2015 panel on 2014 (2013 model year) Macbook, as 2014 isnt’ eligible for trade-in swap which makes the cost sky-high, just insane! Pretty much the price of the macbook itself. Are there any ways to make it work?
Saiba maisI’ve got the same. Any clues? Seems to be a wide spread issue, there must be some common reason. I hope it’s power board not main at least
Saiba maisYou know, I wonder but I experience exactly the same behaviour from exactly the same machine. I’m very sad, as this is a totally opposite to what I expected from Mac (and I had reasons to). It whines sometimes even while easy web browsing. It does it stupidly, temps might rise to ~65 only, but it ramps up and to 50+% and doesn’t stop till it’s ~50. When discrete GPU invokes, even the slightest load in C4D viewport with the lightest model imaginable may crank the fans up to 6000 rpm! INSANE! I cleaned and repasted it, undervolted, I did everything I could but as soon as I launch C4D and start working it kills me with noise. I’m toasted, it’s unbearable. Why does it happens? Is this an issue or a fault of the model? Did previous generation with GT 750m behave the same? How da **** to solve this? I’m about to sell it asap, can’t bare it. Help us please ;(
Saiba maisI’m much interested too. I understand how to bend it back, but will the screen survive? This is the main questions. Suggest us please how to perform it safely? Did anybody try and has an experience to share with us?
Saiba maisWhat I found out: In Windows 10 it's FASTER THAN IT SHOULD BE! 665 CB instead of 640 intended. Probably, because of LM on CPU But it still throttles way lower in ANY MacOS, Mojave nor High Sierra, with or without custom fan control, on automatic nor full fan blast. I've ran ASD testing and everything is fine What da heck?
Saiba maisHi! Finally I’ve got my new heatsink. And, you know… NOTHING CHANGED! Everything is the same, temps are high, clocks are low. What’s the heck is wrong??
Saiba maisPágina 1 de 2
Comentários do guia
Hi!
Did you measure what’s the resistance to ground is for this fuse? I try to repair my camera (actually it’s Sony, but the principle is important) an I get 0.4 ohms to ground. I’m just affraid there are short circuits all around and don’t know whether that’s near normal or not.
I think you should check the connection behind the main board (the power connector which slots in the power circuit under the top LCD)
Anri
@intenditore
71
Reputação
14
Soluções
0
Guias
Membro desde 11/04/13
Votos
17
0