jasbir

Sometimes, it happens that the Epson printer shows paper jam and it won’t print but there is no paper jam in real. If you are sure there is no piece of paper somewhere inside the printer, then try out these methods to fix paper jam. Reset the printer, which might clear a false paper jam error, and then try to print again. With the printer turned on, disconnect the power cord from the printer. (1) Unplug the power cord from the power source. (2) Wait 60 seconds. (3) Reconnect the power cord to a wall outlet and to the printer

No worry Follow these to solve Asus not working issue:- 1 Go for Hard reset > power up the router > Hold the reset button pressed for more than 10 secs > Access the router at the default IP 192.168.1.1 > login username and password is admin. > Manual configure the router again. 2 Wired adaptor setting >Open Network and Sharing Center. Use change adapter settings and then Select your wired adapter. Go into Properties. >Look at your wired adapter settings. >Make sure that Internet Protocol Version 4 (TCP/IPv4) is checked.

changing your DNS settings also works. You can use Google DNS(8.8.8.8 or 8.8.4.4). The Step in below: Go to Settings and tap WiFi Find your network and tap on the info button (i) right next to the Network You see the DNS, tap on the numbers The keyboard will appear and once it does enter the new DNS address. Read For more fixes:- '''Fix iPhone won’t connect'''

Safe mode helps you to start your PS4 system with basic functions and troubleshoot PS4 different problems. Keep in mind that Safe mode will cause data loss. So try to always keep backup your PS4 system data to an external hard drive. Now put PS4 safe mode. 1. If your PS4 is ON then turn it off and remove it from the power outlet. 2. Plug the PS4, press the power button for 5 to 7 seconds. It leads PS4 off again. 3. Keep it off for 2 to 3 minutes. 4. Now press and hold the power key again for approx 20 sec until you hear 2 Beeps. 5. The first beep comes within 5 seconds and the second beep will be after 20 sec. Note:- Here you will see a message on the screen saying connect your PS4 controller by USB cable with the console. 6. Follow the on-screen instruction. 7. Press the PS button on your Controller. 8. Should see the safe mode screen.

If you have original PS4 then it only connect to the 2.4GHz or 5GHz band on your router. If you receive an error on your PS4 that the signal is too weak then just reset or reboot your router.I know this sound weird but trust me it helps maximum of times otherwise turn off other devices on the network. If your PS4 is far from the router then try to move your system as closer to the router as you can. Some time it might be an issue with DNS server setting. Find the setting button on your PS4 menu.In that search for network and in that select set yp internet connection. After that select custom from there. Select the WiFi network from your router. Once you connected to the network select do not specify option. Select the DNS setting on manual. Setup primary DNS on 8.8.8.8 and secondary DNS on 8.8.4.4 Source:- Fix PS4 keeps disconnecting If you are not getting all these steps then use Ethernet cable to connect your PS4 and Router. problem solved.

fix Paper jam solutions for Epson Printer 1. Power off the printer for 12 to 20 minutes. 2. Remove the toner cartridge, if present then gently and carefully give the printer a few upside-down shakes. 3. Try removing all ink cartridges and reinstall them one at a time. 4. Move the carriage over to the far left and bring back it to position. May be it is out of position. 5. Prepare one sheet of thick paper such as glossy paper and with the power off gently push the sheet through the paper path of the printer. 6. If you do not find anything wrong bring the printer to a repair center.

(1) Switch off all the devices modem, router and computers also unplug their power cables. (2) Wait at least 1 to 5 minutes. We have found in some instances you need to wait at least 15 minutes (3) Plug the power cords back in, but don’t switch them on. (4) First turn on the modem and then wait for a few minutes for it to settle and all the lights to become stable. (5) Next switch on the router (if a separate device) and then wait for a few minutes for it to settle and all the lights to become stable. (6) Now turn on your computer, You should now be able to access the Internet.