Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
-
-
Encha uma panela ou frigideira com água suficiente para submergir completamente um iOpener.
-
Aqueça a água até ferver. Desligue o fogo.
-
Coloque um iOpener na água quente por 2 a 3 minutos. Certifique-se de que o iOpener esteja totalmente submerso na água.
-
Use um pegador para retirar o iOpener aquecido da água quente.
-
Seque bem o iOpener com uma toalha.
-
Sua bolsa térmica iOpener está pronta para o uso! Se precisar reaquecer o iOpener, aqueça a água até ferver, desligue o fogo e coloque o iOpener na água por 2 a 3 minutos.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
If your display glass is cracked, keep further breakage contained and prevent bodily harm during your repair by taping the glass.
-
Lay overlapping strips of clear packing tape over the iPad's display until the whole face is covered.
-
Do your best to follow the rest of the guide as described. However, once the glass is broken, it will likely continue to crack as you work, and you may need to use a metal prying tool to scoop the glass out.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Handling it by the tab, place the heated iOpener on the side of the iPad to the left of the home button assembly.
-
Let the iOpener sit for about five minutes to soften the adhesive beneath the glass.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully place a suction cup halfway up the heated side.
-
Be sure the cup is completely flat on the screen to get a tight seal.
-
While holding the iPad down with one hand, pull up on the suction cup to slightly separate the front panel glass from from the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
While holding the glass up with the suction cup, slide the point of an opening pick into the gap between the glass and body of the iPad.
-
Pull the suction cup's plastic nub to release the vacuum seal and remove the suction cup from the display assembly.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Reheat and reapply the iOpener.
-
Let it rest for a few minutes to reheat the left edge of the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place a second opening pick alongside the first and slide the pick down along the edge of the iPad, releasing the adhesive as you go.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Continue moving the opening pick down the side of the display to release the adhesive.
-
If the opening pick gets stuck in the adhesive, "roll" the pick along the side of the iPad, continuing to release the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Take the first pick you inserted and slide it up toward the top corner of the iPad.
-
If you can see the tip of the opening pick through the front glass, don't panic—just pull the pick out a little bit. Most likely, everything will be fine, but try to avoid this as it may deposit adhesive on the front of the LCD that is difficult to clean off.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Reheat the iOpener and place it on the top edge of the iPad, over the front-facing camera.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the opening pick around the top left corner of the iPad to separate the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the opening pick along the top edge of the iPad, stopping just before you reach the camera.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the pick out slightly, and slide the very tip gently along the top of the front-facing camera section of the top edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the opening pick in the iPad slightly past the front-facing camera.
-
Take a second pick and insert it to the left of the camera, where the first pick just was. Slide it back to the corner to completely cut any remaining adhesive.
-
Leave the second pick in place to prevent the corner adhesive from re-sealing as it cools.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert the previous pick deeper into the iPad and slide it away from the camera toward the corner.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the three picks in the corners of the iPad to prevent re-adhering of the front panel adhesive.
-
Reheat the iOpener and place it on the remaining long side of the iPad—along the volume and lock buttons.
-
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the top right opening pick around the corner to fully release the top edge of the glass.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert a new opening pick and slide it to the middle of the right edge of the iPad, releasing the adhesive as you go.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Continue to slide the pick down the right edge of the iPad, releasing the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Leave the opening picks in place and reheat the iOpener.
-
Set the reheated iOpener on the home button end of the iPad and let it rest for a few minutes to soften the adhesive beneath the glass.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the lower left pick to the lower left corner to cut the adhesive on that corner.
-
Leave the pick at the corner. Do not pry any farther, and do not remove the pick from the iPad.
-
Antennas
-
Home button cavity
-
Digitizer cable
-
The following steps will direct you where to pry to avoid damage to these components. Only apply heat and pry where directed.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
With a new pick, slice gently over the left-hand antenna, stopping before the home button.
-
Leave the pick in place before moving on.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert the tip of one last pick next to the previous step's pick, and slide it beneath the home button.
-
Insert the pick slightly deeper and work it back toward the home button.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Reheat and reapply the iOpener to the top bezel of the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
At the top of the iPad opposite the home button, you should have a pick lodged into each corner. Twist the picks to lift the glass slightly, separating the last of the adhesive along all four edges.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift slowly and gently to further detach the adhesive along the lower edge.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Once all of the adhesive has been separated, open the front glass like a page in a book and rest it on your workspace.
-
If reusing the front panel assembly during reassembly, you will need to replace your display adhesive. Use our display adhesive application guide to reapply your display adhesive and reseal your device.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Rock the camera housing up on one edge to free it from the adhesive and remove it from the front panel.
-
Return the front-facing camera housing to its recess in the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following Phillips #00 screws securing the LCD:
-
Three 3.3 mm screws
-
One 4.5 mm screw
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert the flat end of a spudger under the LCD between it and the LCD shield plate and lift gently.
-
Run a thin string (like floss or fishing line) under the display, starting from the top then working your way down
-
Use a thin, flexible card or plastic money note to cut through the adhesive starting from the top.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert the spudger between the LCD and LCD shield plate and slide it to the far edge of the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Hold the LCD with one hand, and the rear body of the iPad with the other.
-
Gently pull the LCD away from the speakers to separate the tape, being careful not to pull on the digitizer cable.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Flip the iPad LCD like a page in a book, lifting near the camera and turning it over the home button end of the rear case.
-
Lay the LCD on the front panel glass to allow access to the display cables.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the tip of a spudger between the LCD and the adhesive tabs to free the display.
-
Push gently between each of the two adhesive tabs; be careful not to damage any of the nearby cables.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the seven 1.8 mm Phillips #00 screws from the LCD shield plate.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the flat end of a spudger to pry the LCD shield plate up and out of the iPad.
-
Remove the LCD shield plate.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following Phillips #00 screws from the display cable bracket:
-
One 2.8 mm screw
-
Three 1.4 mm screws
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the tip of a spudger to lift the home button cable up off of its socket on the logic board.
-
Fold the home button ribbon cable out of the way.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the tip of a spudger to gently lift the battery connector up off its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the tip of a spudger to lift the LCD connector up off its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the tip of a spudger to lift the digitizer cable connector straight up off of its socket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slide the flat end of a spudger under the battery side of the digitizer board to begin separating it from the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift the digitizer board up to free the last of the adhesive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift and remove the front panel assembly from the iPad.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use an opening pick to break up the adhesive holding the home button ribbon cable to the digitizer cable.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Insert an opening pick between the home button ribbon cable and the digitizer.
-
Slide the pick along the front panel, towards the home button, to continue separating the home button ribbon cable from the front panel.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use an opening pick to lift the home button control hardware off the back of the front panel.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Peel up the last of the tape holding the home button ribbon cable in place by inserting an opening pick between the cable and the digitizer.
-
Continue sliding the pick underneath the cable until it is wholly separated from the front panel
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a plastic opening tool to pry the home button bracket off the back of the digitizer.
-
Remove the home button bracket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Prepare an iOpener and lay it over the lower edge of the digitizer to loosen the adhesive holding the home button gasket in place.
-
Flip the digitizer panel over and gently push the home button up out of its slot in the front panel.
-
Cancelar: não concluí este guia.
103 outras pessoas executaram este guia.
18 comentários
Why do you skip the part about moving the old home button to the new digitizer?
Kind of an important step. Is it easy?
Agreed. Regluing the home button to the new digitizer is tedious.
I'm pretty sure the digitizer and the LCD are glued together with OCA on the 3rd generation iPad mini... separating/replacing them requires the equipment that is used for iPhones. You can't use LOCA glue in place of OCA because apple didn't think it was a good idea to seal the backlight to the LCD. The iPad mini and the iPad air 2nd Gen are repaired the same way, which is different than the previous versions of ipads. Please correct me if I'm wrong
You are incorrect. They are indeed separate.