Introdução

This guide is for the replacement of tweeter diaphragm for the Sonos One.

Important: Accessing the internals of the Sonos One will void the factory warranty and make the unit rejected for factory repair, even if warranty is expired.

Disconnect all power cords. Remove the rubber foot and plastic screw guard on the bottom of the device using a plastic opening tool. Remove the rubber foot and plastic screw guard on the bottom of the device using a plastic opening tool.
  • Disconnect all power cords.

  • Remove the rubber foot and plastic screw guard on the bottom of the device using a plastic opening tool.

Adicionar comentário

Remove the four 10mm Torx T10 screws from the bottom of the speaker. Remove the four 10mm Torx T10 screws from the bottom of the speaker. Remove the four 10mm Torx T10 screws from the bottom of the speaker.
  • Remove the four 10mm Torx T10 screws from the bottom of the speaker.

Adicionar comentário

Remove the bottom cover by squeezing the protective cover slightly while pushing up with your fingers. Remove the bottom cover by squeezing the protective cover slightly while pushing up with your fingers.
  • Remove the bottom cover by squeezing the protective cover slightly while pushing up with your fingers.

Adicionar comentário

The protective cover clip is very thin and deforms easily. Remove the single 8mm Torx T10 screw and protective cover clip. Remove the single 8mm Torx T10 screw and protective cover clip.
  • The protective cover clip is very thin and deforms easily.

  • Remove the single 8mm Torx T10 screw and protective cover clip.

Adicionar comentário

Slide the protective cover upwards to remove. Slide the protective cover upwards to remove.
  • Slide the protective cover upwards to remove.

Adicionar comentário

Use the pointed end of a spudger to remove the covers that hide the screws. Remove the four 9mm Torx T8 screws from around the perimeter of the control panel. Remove the four 9mm Torx T8 screws from around the perimeter of the control panel.
  • Use the pointed end of a spudger to remove the covers that hide the screws.

  • Remove the four 9mm Torx T8 screws from around the perimeter of the control panel.

Adicionar comentário

With the front of the unit facing you, lift the control panel up using your thumbs. There's a ribbon cable attaching the control panel to the speaker so work slowly.
  • With the front of the unit facing you, lift the control panel up using your thumbs.

  • There's a ribbon cable attaching the control panel to the speaker so work slowly.

Adicionar comentário

Use a spudger to flip up the retaining flap on the control panel ribbon cable ZIF socket. Pull the control panel ribbon cable out of its socket. Pull the control panel ribbon cable out of its socket.
  • Use a spudger to flip up the retaining flap on the control panel ribbon cable ZIF socket.

  • Pull the control panel ribbon cable out of its socket.

Adicionar comentário

Pull the control panel away from the speaker to separate. Pull the control panel away from the speaker to separate.
  • Pull the control panel away from the speaker to separate.

Adicionar comentário

Remove the six 9mm Torx T8 screws from the motherboard panel. Remove the six 9mm Torx T8 screws from the motherboard panel. Remove the six 9mm Torx T8 screws from the motherboard panel.
  • Remove the six 9mm Torx T8 screws from the motherboard panel.

Adicionar comentário

Using a plastic opening tool, separate the motherboard from the speaker. Using a plastic opening tool, separate the motherboard from the speaker.
  • Using a plastic opening tool, separate the motherboard from the speaker.

Adicionar comentário

Using your thumb, disconnect the speaker cable from the motherboard. Using your thumb, disconnect the speaker cable from the motherboard. Using your thumb, disconnect the speaker cable from the motherboard.
  • Using your thumb, disconnect the speaker cable from the motherboard.

Adicionar comentário

Disconnect the power adapter plug from the motherboard using your thumb. Disconnect the power adapter plug from the motherboard using your thumb. Disconnect the power adapter plug from the motherboard using your thumb.
  • Disconnect the power adapter plug from the motherboard using your thumb.

Adicionar comentário

Using the pointed end of the spudger, disconnect the red, green, and yellow cables connecting the WiFi transmitter/receiver. Using the pointed end of the spudger, disconnect the red, green, and yellow cables connecting the WiFi transmitter/receiver. Using the pointed end of the spudger, disconnect the red, green, and yellow cables connecting the WiFi transmitter/receiver.
  • Using the pointed end of the spudger, disconnect the red, green, and yellow cables connecting the WiFi transmitter/receiver.

Adicionar comentário

Remove the motherboard panel from the speaker housing. Remove the motherboard panel from the speaker housing.
  • Remove the motherboard panel from the speaker housing.

Adicionar comentário

The woofer is highly magnetic, making removal of the metal screws sometimes difficult. Remove the two 9mm Torx T8 screws from the power adapter plug. Remove the power adapter receptacle from its housing slot.
  • The woofer is highly magnetic, making removal of the metal screws sometimes difficult.

  • Remove the two 9mm Torx T8 screws from the power adapter plug.

  • Remove the power adapter receptacle from its housing slot.

Adicionar comentário

Disconnect the woofer cables. If removing the tabs is difficult, the flat end of the spudger may be used to depress the middle tab and then the tab may be pulled to disconnect. If removing the tabs is difficult, the flat end of the spudger may be used to depress the middle tab and then the tab may be pulled to disconnect.
  • Disconnect the woofer cables.

  • If removing the tabs is difficult, the flat end of the spudger may be used to depress the middle tab and then the tab may be pulled to disconnect.

Adicionar comentário

Disconnect the cables from the tweeter. Disconnect the cables from the tweeter. Disconnect the cables from the tweeter.
  • Disconnect the cables from the tweeter.

Adicionar comentário

Remove the four 10mm Torx T10 screws from the tweeter. Remove the tweeter from the speaker housing. Remove the tweeter from the speaker housing.
  • Remove the four 10mm Torx T10 screws from the tweeter.

  • Remove the tweeter from the speaker housing.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Marcus Glowa

Member since: 14-02-2018

653 reputação

5 Guides authored

Equipe

USF Tampa, Team S2-G1, Nance Spring 2018 Membro de USF Tampa, Team S2-G1, Nance Spring 2018

USFT-NANCE-S18S2G1

3 Membros

5 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 17

Todo: 84