Conserte seus objetos Comunidade Loja

Ryobi CSB125 Motor Replacement

Introdução

This guide will show you how to properly access the internals to the motor housing to your Ryobi CSB125 circular saw. If you hear a humming noise when pressing the trigger, or while operating the saw smoke forms, then most likely the motor has gone bad. This troubleshooting page will help diagnose any potential problems occurring due to a faulty motor. In the event that a new motor is needed, this guide will show the steps to properly install a new one. The only tools you will need are a #2 Phillips screwdriver, a 7”/32 allen key, and a T20 torx screwdriver.

O que você precisa

  1. Ryobi CSB125 Motor Replacement, Motor: passo 1, imagem 1 %32

    • Place the saw on a flat surface with the blade facing up.

    • Make sure that the saw is unplugged from any power source.

    Editar

  2. Ryobi CSB125 Motor Replacement: passo 2, imagem 1 %32 Ryobi CSB125 Motor Replacement: passo 2, imagem 2 %32

    • Remove the bumper by using the T20 torx screwdriver to loosen the M5 x 20mm screw.

    Editar

  3. Ryobi CSB125 Motor Replacement: passo 3, imagem 1 %32 Ryobi CSB125 Motor Replacement: passo 3, imagem 2 %32

    • Use the 7”/32 allen key to loosen the 5/16-18 x 9/16 in. blade screw.

    Editar

  4. Ryobi CSB125 Motor Replacement: passo 4, imagem 1 %32

    • Remove the 5/16-18 x 9/16 in. blade screw, spring washer, the outer blade washer, the blade, and the inner blade washer.

    Editar

  6. Ryobi CSB125 Motor Replacement: passo 5, imagem 1 %32 Ryobi CSB125 Motor Replacement: passo 5, imagem 2 %32 Ryobi CSB125 Motor Replacement: passo 5, imagem 3 %32

    • Use the #2 Phillip screwdriver to remove the four M4x16mm screws shown.

    • You will need to rotate the protective shell around in order to access them.

    Editar

  7. Ryobi CSB125 Motor Replacement: passo 6, imagem 1 %32

    • Remove the lower blade guard support assembly from the rest of the saw.

    Editar

  8. Ryobi CSB125 Motor Replacement: passo 7, imagem 1 %32

    • Flip the saw over and place the saw down on a flat surface with the motor facing up.

    Editar

  9. Ryobi CSB125 Motor Replacement: passo 8, imagem 1 %32

    • Use the Phillips #2 screwdriver to remove the five M4x16mm screws.

    Editar

  10. Ryobi CSB125 Motor Replacement: passo 9, imagem 1 %32

    • Use the Phillips #2 screwdriver to remove the two M45x35mm screws.

    Editar

  11. Ryobi CSB125 Motor Replacement: passo 10, imagem 1 %32 Ryobi CSB125 Motor Replacement: passo 10, imagem 2 %32

    • Use the Phillips #2 screwdriver to remove the two M4x16mm screws holding down the end cover.

    • Pull off the end cover.

    Editar

  12. Ryobi CSB125 Motor Replacement: passo 11, imagem 1 %32

    • Use the Phillips #2 screwdriver to remove the M45x35mm screw holding down the motor housing.

    Editar

  13. Ryobi CSB125 Motor Replacement: passo 12, imagem 1 %32

    • Remove the motor housing for access to the internal motor components.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

3 outras pessoas executaram este guia.

Autor(a)

com 1 outro contribuidor

Curtis Melo

Membro desde: 10/31/19

1.066 Reputação

Autoria de 5 guias

Emblemas: 10

+7 outros emblemas

Equipe

UMass Dartmouth, Team S2-G1, Barthe Fall 2019 Membro de UMass Dartmouth, Team S2-G1, Barthe Fall 2019

UMASSD-BARTHE-F19S2G1

Membros da 3

Autoria de 5 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 8

Últimos 30 dias: 18

Duração total: 575