Ir para o conteúdo principal

Introdução

This guide outlines the procedure for accessing the device circle pad. To access the circle pad, the entire device must be opened. This might be intimidating at first, but as long as the guide directions are followed, no damage to the device is expected. For more information, refer to our troubleshooting page.

  1. Before starting the disassembly, remove
    • Before starting the disassembly, remove

    • The stylus

    • Any game cartridge

    • The SD card

  2. Unscrew the four 6mm tri-point screws located at the four corners of the bottom panel.
    • Unscrew the four 6mm tri-point screws located at the four corners of the bottom panel.

  3. Be careful when separating the bottom panel from the front casing to avoid breaking the three cables connected to the motherboard (two on each side and one in the rear). Using a spudger, separate the back panel from the front casing by gently prying around the panel.
    • Be careful when separating the bottom panel from the front casing to avoid breaking the three cables connected to the motherboard (two on each side and one in the rear).

    • Using a spudger, separate the back panel from the front casing by gently prying around the panel.

    • There are many clips along the hinge of the case, so it is recommended to work your way along one short side and the two long sides before finishing the last short side.

  4. Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora

    Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora
  5. Using tweezers, disconnect the two cables that connect the rear buttons on either side to the motherboard by gently pulling them upwards. Using tweezers, disconnect the two cables that connect the rear buttons on either side to the motherboard by gently pulling them upwards. Using tweezers, disconnect the two cables that connect the rear buttons on either side to the motherboard by gently pulling them upwards.
    • Using tweezers, disconnect the two cables that connect the rear buttons on either side to the motherboard by gently pulling them upwards.

  6. Using a spudger, lift out the battery. Be aware that there is a sticky pad holding the battery into its tray. It may be necessary to use multiple tools to gently pry the battery away from the tray and motherboard.
    • Using a spudger, lift out the battery.

    • Be aware that there is a sticky pad holding the battery into its tray. It may be necessary to use multiple tools to gently pry the battery away from the tray and motherboard.

  7. To more easily access this ribbon cable, flip the device so the back casing faces upwards. Gently slide the back casing forward, revealing the ribbon cable connecting to the motherboard. Using a spudger, pry up the ZIF connector holding the ribbon cable. Pull the ribbon towards the bottom casing and out of the connector.
    • To more easily access this ribbon cable, flip the device so the back casing faces upwards. Gently slide the back casing forward, revealing the ribbon cable connecting to the motherboard.

    • Using a spudger, pry up the ZIF connector holding the ribbon cable.

    • Pull the ribbon towards the bottom casing and out of the connector.

  8. Remove the two 7.5mm phillips screws using a PH000 screwdriver. Gently flip over the circle pad. Be aware that the pad is pressed into the back of the circle pad on the front of the case. Gentle prying will be necessary to pry if from the back of the circle pad.
    • Remove the two 7.5mm phillips screws using a PH000 screwdriver.

    • Gently flip over the circle pad. Be aware that the pad is pressed into the back of the circle pad on the front of the case. Gentle prying will be necessary to pry if from the back of the circle pad.

    • Be aware that there is a black plastic disc that sits between the circle pad module and the circle pad stick. During reassembly, stand the unit on end and hang the plastic disc on the circle pad module and hold the stick from the front to press them back together.

  9. Using a spudger, lift up the ZIF connector (the hinge is located on the side closest to where the cable connects). Remove the circle pad by pulling it away from  the connector. Remove the circle pad by pulling it away from  the connector.
    • Using a spudger, lift up the ZIF connector (the hinge is located on the side closest to where the cable connects).

    • Remove the circle pad by pulling it away from the connector.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Tim Newman

Membro desde: 25-09-2017

860 Reputation

4 Guias de autoria

Team

Cal Poly, Team S18-G6, Forte Fall 2017 Membro de Cal Poly, Team S18-G6, Forte Fall 2017

CPSU-FORTE-F17S18G6

5 Membros

4 Guias de autoria

I can’t seem to find a New 2ds XL circle pad replacement online, does anyone know if a regular 2ds circle pad works? (Or perhaps a 3ds one?)

Dvdcd - Responder

Excellent guide, although I believe the 2ds XL requires a Y00 and not a Y0

Gabrielle Watson - Responder

Add Comment

View Statistics:

Past 24 Hours: 3

Past 7 Days: 14

Past 30 Days: 72

All Time: 2,328