Introdução

The screen is a common breaking point for cellular phones, and can be replaced to repair an unusable phone.

Remove the four rubber stoppers from around the screen with a pin to reveal four screws. Remove the four rubber stoppers from around the screen with a pin to reveal four screws. Remove the four rubber stoppers from around the screen with a pin to reveal four screws.
  • Remove the four rubber stoppers from around the screen with a pin to reveal four screws.

Adicionar comentário

Remove the four 3.8 mm T-6 Torx screws. Remove the four 3.8 mm T-6 Torx screws.
  • Remove the four 3.8 mm T-6 Torx screws.

Adicionar comentário

Separate the cover from the edges using a plastic opening tool. Separate the cover from the edges using a plastic opening tool.
  • Separate the cover from the edges using a plastic opening tool.

Adicionar comentário

With the edges separated, close the phone and lift off the faceplate with your fingers. With the edges separated, close the phone and lift off the faceplate with your fingers.
  • With the edges separated, close the phone and lift off the faceplate with your fingers.

Adicionar comentário

Gently peel off the plastic film from the metal plate above the camera lens as shown.
  • Gently peel off the plastic film from the metal plate above the camera lens as shown.

Adicionar comentário

Insert the spudger into the slots marked and gently pry upwards to remove the metal cover. Repeat the previous bullet for the two corresponding tabs on the opposite side of the phone.
  • Insert the spudger into the slots marked and gently pry upwards to remove the metal cover.

  • Repeat the previous bullet for the two corresponding tabs on the opposite side of the phone.

Adicionar comentário

Lift and peel back the tape attaching metal casing to body of the phone. Gently lift the metal cover and remove to expose the circuit board.
  • Lift and peel back the tape attaching metal casing to body of the phone.

  • Gently lift the metal cover and remove to expose the circuit board.

Adicionar comentário

Using a plastic opening tool, pry or lift open the pink door shown. After the door is open, gently pull on the ribbon cable's corner to separate it from the board.
  • Using a plastic opening tool, pry or lift open the pink door shown.

    • After the door is open, gently pull on the ribbon cable's corner to separate it from the board.

  • Work out the ribbon cable's end slowly and gently to avoid damaging the pink door port.

Adicionar comentário

Use a plastic opening tool to dislodge and remove the rubber camera cover. Use a plastic opening tool to dislodge and remove the rubber camera cover. Use a plastic opening tool to dislodge and remove the rubber camera cover.
  • Use a plastic opening tool to dislodge and remove the rubber camera cover.

Adicionar comentário

Lift the top ribbon cable, with camera attached, up and away from the rest of the phone. Lift the top ribbon cable, with camera attached, up and away from the rest of the phone.
  • Lift the top ribbon cable, with camera attached, up and away from the rest of the phone.

Adicionar comentário

Pull the ribbon cable up and out of the way to get access to the circuit board-screen unit. Using a plastic opening tool, gently pry and remove the circuit board-screen unit in both screens. Using a plastic opening tool, gently pry and remove the circuit board-screen unit in both screens.
  • Pull the ribbon cable up and out of the way to get access to the circuit board-screen unit.

  • Using a plastic opening tool, gently pry and remove the circuit board-screen unit in both screens.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Blair Frandeen

Member since: 02-10-2010

19 reputação

8 Guides authored

Equipe

Cal Poly, Team 7-50, Amido Fall 2010 Membro de Cal Poly, Team 7-50, Amido Fall 2010

CPSU-AMIDO-F10S7G50

4 Membros

24 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Todo: 2,628