Introdução

Replace a broken screen in your Gateway SA1 laptop.

Move the latch to the right of the battery to unlock.
  • Move the latch to the right of the battery to unlock.

Adicionar comentário

Slide the latch on the left directly below the battery to unlock and pull out the battery as shown.
  • Slide the latch on the left directly below the battery to unlock and pull out the battery as shown.

  • The latch must be held in position to remove the battery.

Adicionar comentário

Remove the hinge covers by lifting each with the sharp point of the spudger. Notice that the middle cover has a different shape and is more difficult to remove.
  • Remove the hinge covers by lifting each with the sharp point of the spudger.

    • Notice that the middle cover has a different shape and is more difficult to remove.

Adicionar comentário

Remove the six screw covers on the front bezel with the sharp point of the spudger. The bottom two are more difficult to remove.
  • Remove the six screw covers on the front bezel with the sharp point of the spudger.

    • The bottom two are more difficult to remove.

Adicionar comentário

Remove the six 5.9 mm Philips screws securing the screen bezel.
  • Remove the six 5.9 mm Philips screws securing the screen bezel.

Adicionar comentário

Remove the front bezel by prying it off with the wedged end of the spudger. Verify that your spudger does not touch the LCD. The screen inverter is now exposed below the LCD.
  • Remove the front bezel by prying it off with the wedged end of the spudger.

  • Verify that your spudger does not touch the LCD.

    • The screen inverter is now exposed below the LCD.

Adicionar comentário

Remove the single 3.8mm Phillips screw mounting the screen inverter to the computer.
  • Remove the single 3.8mm Phillips screw mounting the screen inverter to the computer.

Adicionar comentário

Use your finger, or the spudger, to pry the inverter board out. This exposes the wires behind it.
  • Use your finger, or the spudger, to pry the inverter board out.

    • This exposes the wires behind it.

Adicionar comentário

Unplug the LCD back light cables from the right side of the screen inverter.
  • Unplug the LCD back light cables from the right side of the screen inverter.

Adicionar comentário

Remove the six screws that mount the screen to the hinge mounts. Two 2.5 mm Phillips screws.
  • Remove the six screws that mount the screen to the hinge mounts.

    • Two 2.5 mm Phillips screws.

    • Four 3.8 mm Phillips screws.

Adicionar comentário

Unplug the cable from the webcam board.
  • Unplug the cable from the webcam board.

    • Be gentle, do not use excessive force or you may break the connection.

Adicionar comentário

Separate the screen from the display cover.
  • Separate the screen from the display cover.

    • Do not touch the back of the screen.

Adicionar comentário

Remove the three tape strips that hold down the cables. Be careful not to tear any of the tape. The piece holding down the webcam wires is especially delicate.
  • Remove the three tape strips that hold down the cables.

    • Be careful not to tear any of the tape. The piece holding down the webcam wires is especially delicate.

Adicionar comentário

Unplug the display data cable from the screen connector. This connection is very fragile; do not use excessive force.
  • Unplug the display data cable from the screen connector.

    • This connection is very fragile; do not use excessive force.

    • The screen should now be free from all wire connections.

Adicionar comentário

Remove the four 2.8 mm Phillips screws that secure the screen to the mounting bracket using a screwdriver.
  • Remove the four 2.8 mm Phillips screws that secure the screen to the mounting bracket using a screwdriver.

    • There will be two screws on either side of the mounting bracket.

Adicionar comentário

You can now remove and replace the screen.
  • You can now remove and replace the screen.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

2 outras pessoas concluíram este guia.

Diego Carteno

Member since: 15-04-2010

241 reputação

7 Guides authored

Equipe

Cal Poly, Team 24-20, Regan Spring 2010 Membro de Cal Poly, Team 24-20, Regan Spring 2010

CPSU-REGAN-S10S24G20

4 Membros

7 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 2

Últimos 30 dias: 13

Todo: 17,879