Conserte seus objetos Comunidade Loja

Etekcity Lasergrip 1080 Screen Replacement

Introdução

This guide will show you how to replace a faulty screen. This will use a screwdriver and a plastic opening tool. There are no hazards involved with this guide.

O que você precisa

  1. Etekcity Lasergrip 1080 Screen Replacement, Battery: passo 1, imagem 1 %32

    • Pull the battery cover away from the handle by gripping near the thumb groove.

    Editar

  2. Etekcity Lasergrip 1080 Screen Replacement: passo 2, imagem 1 %32

    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

    Editar

  3. Etekcity Lasergrip 1080 Screen Replacement: passo 3, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement: passo 3, imagem 2 %32

    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

    Editar

  4. Etekcity Lasergrip 1080 Screen Replacement, Buttons: passo 4, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement, Buttons: passo 4, imagem 2 %32

    • Remove the battery cover from the device by pulling it straight out.

    Editar

  6. Etekcity Lasergrip 1080 Screen Replacement: passo 5, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement: passo 5, imagem 2 %32

    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

    Editar

  7. Etekcity Lasergrip 1080 Screen Replacement: passo 6, imagem 1 %32

    • Remove the two 3.1 mm Phillips #0 screws.

    Editar

  8. Etekcity Lasergrip 1080 Screen Replacement: passo 7, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement: passo 7, imagem 2 %32

    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

    Editar

  9. Etekcity Lasergrip 1080 Screen Replacement: passo 8, imagem 1 %32

    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

    Editar

  10. Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: passo 9, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement, Etekcity Lasergrip 1080 Trigger Replacement: passo 9, imagem 2 %32

    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

    Editar

  11. Etekcity Lasergrip 1080 Screen Replacement, Screen: passo 10, imagem 1 %32

    • Carefully pull the motherboard out of its slot in the body of the device.

    Editar

  12. Etekcity Lasergrip 1080 Screen Replacement: passo 11, imagem 1 %32 Etekcity Lasergrip 1080 Screen Replacement: passo 11, imagem 2 %32

    • Unscrew the two 3.4 mm screws on the motherboard.

    Editar

  13. Etekcity Lasergrip 1080 Screen Replacement: passo 12, imagem 1 %32

    • Take off the cover and separate the parts.

    • All of these parts are fragile and mishandling them may cause damage.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 2 outros contribuidores

Carlos Pineda

Membro desde: 08/27/15

195 Reputação

Autoria de 1 guia

Emblemas: 5

+2 outros emblemas

Equipe

USF Tampa, Team 5-1, Blackwell Fall 2015 Membro de USF Tampa, Team 5-1, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G1

Membros da 3

Autoria de 9 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 3

Últimos 7 dias: 6

Últimos 30 dias: 18

Duração total: 919