Ir para o conteúdo principal

Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement

O que você precisa

  1. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Battery: passo 1, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Battery: passo 1, imagem 2 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Battery: passo 1, imagem 3 %32
    • Pull back on the release tabs to disconnect the battery pack from the housing.

    • When installing a new battery, you may need to charge it before using it.

  2. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Motor-Shaft Assembly: passo 2, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Motor-Shaft Assembly: passo 2, imagem 2 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Motor-Shaft Assembly: passo 2, imagem 3 %32
    • Remove the two screws from the back of the device with the TR10 Torx Security screwdriver.

    • Make sure you have removed the battery before proceeding as accidentally powering-on the device while disassembling is dangerous due to the high-speed components inside.

  3. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 3, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 3, imagem 2 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 3, imagem 3 %32
    • Lift off the unscrewed plastic cover at an angle, away from the tip of the device.

    • Gently lift the cover. It won't take much force to remove it.

  4. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 4, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 4, imagem 2 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 4, imagem 3 %32
    • Lift the tip of the motor-shaft assembly gently, then pull the assembly out.

    • The blue battery contact and the spring for the shaft lock button may pop out when you remove the motor-shaft assembly. Make sure to keep track of these pieces, as they are very small.

  5. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement, Shaft Lock Assembly: passo 5, imagem 1 %32
    • There are two pieces that make up the shaft lock assembly:

    • The key.

    • The wire ring.

    • The key holds the wire ring in place, and the wire ring secures the motor shaft.

  6. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 6, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 6, imagem 2 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 6, imagem 3 %32
    • Remove the wire ring from the device.

    • The wire ring may have come out when the motor-shaft assembly was removed.

    • Remove the key from its slot.

  7. Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 7, imagem 1 %32 Dremel 7300 MiniMite Cordless Shaft Lock Assembly Replacement: passo 7, imagem 2 %32
    • Ensure that the shaft lock assembly fits together properly when reassembling the device.

    • The notch in the wire ring should fit on the key as pictured.

Conclusão

To reassemble your device, follow these instructions in reverse order.

3 outras pessoas executaram este guia.

Kat

Membro desde: 02/10/16

840 Reputação

Autoria de 3 guias

Equipe

USF Tampa, Team 3-4, Sullivan Spring 2016 Membro de USF Tampa, Team 3-4, Sullivan Spring 2016

USFT-SULLIVAN-S16S3G4

Membros da 4

Autoria de 4 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 7

Últimos 30 dias: 18

Duração total: 1,806