Dell Alienware 13 R3 Computer Base Replacement - Guia de Reparo iFixit

Participe da comunidade de reparos - Criar conta

Introdução

In this guide, we show you how to remove and replace the computer base.

O que você precisa

1. Passo 1 Loosen the Screws
  WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  
  Loosen the five captive screws that secure the base cover to the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
2. Passo 2 Pry the Base Cover
  Using a plastic scribe, gently pry the base cover to release the tabs on the base cover from the slots on the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
3. Passo 3 Lift the Base Cover
  Lift the base cover off the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
4. Passo 4 Disconnect the Battery Cable
  Using a plastic scribe, disconnect the battery cable from the system board.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
5. Passo 5 Press and Hold the Power-Button
  Press and hold the power button for five seconds to ground the system board.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
6. Passo 6 Slide the Tabs
  Slide the tabs on the NEW base cover into the slots on the computer base and snap the base cover into place
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
7. Passo 7 Tighten the Five Captive Screws
  Tighten the five captive screws that secure the base cover to the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
1. Passo 8 Remove the Screw
  WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  
  Remove the screw (M2x3) that secures the solid-state drive to the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
3. Passo 9 Lift and Slide the Solid-State Drive
  Lift and slide the solid-state drive from the solid-state drive slot.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
4. Passo 10 Align the Notch
  Align the notch on the NEW solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive slot.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
5. Passo 11 Press the Memory Module
  Press the memory module down until it clicks into place.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
1. Passo 12 Remove the Screws
  Remove the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
2. Passo 13 Using a Plastic Scribe
  Using a plastic scribe, gently release the tabs that secure rear-I/O cover to the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
3. Passo 14 Removing the Rear-I/O
  Slide and remove the rear-I/O cover from the computer base.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
4. Passo 15 Sliding the Rear-I/O
  Slide the NEW rear-I/O cover into the slots on the computer base and snap the rear-I/O cover into place.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
5. Passo 16 Replace the two Screws
  Replace the two screws (M2.5x6L) that secure the rear-I/O cover to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
1. Passo 17 Remove the Screws
  WARNING: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before Working Inside Your Computer. After working inside your computer, follow the instructions in After Working Inside Your Computer.
  
  Remove the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
2. Passo 18 Remove the Screw
  Remove the (M2x3) screw that secures the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
3. Passo 19 Remove the Two Screws
  Remove the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
4. Passo 20 Lift the Computer Base
  Lift the computer base from the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
5. Passo 21 Align the Screw Holes
  Align the screw holes on the NEW computer base with the screw holes on the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
6. Passo 22 Replace the Screws
  Replace the two (M2.5x6L) screws that secure the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
7. Passo 23 Replace the Screw
  Replace the (M2x3) screw that secures the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024
8. Passo 24 Replace the Eleven Screws
  Replace the eleven (M2.5x6L) screws that secure the computer base to the palm-rest assembly.
  Editar
  
  Pergunte ao FixBot
  
  Comentar
  
  1024

Conclusão

To reassemble your device, follow these instructions in reverse order.

Cancelar: não concluí este guia.

Autor(a)

com 2 outros contribuidores

Terrence15

Membro desde: 12/18/17

80.125 Reputação

Autoria de 441 guias

+26 outros emblemas

Equipe

RampUP America, Inc. Membro de RampUP America, Inc.

Community

45 Membros

Autoria de 11.849 guias

0Comentários do guia

Visualizações:

Últimas 24 horas: 3

Últimos 7 dias: 10

Últimos 30 dias: 43

Ao todo: 1,039