Pular para o conteúdo principal

Introdução

Removing the top cover of camera gives access to the LCD screen, control dial, and flash.

Peças

Nenhum componente especificado.

  1. Locate the battery door/camera grip on the left side of the camera and lift the rotating removal tab.
    • Locate the battery door/camera grip on the left side of the camera and lift the rotating removal tab.

  2. Twist the tab clockwise to unlock the door, then pull outward from the camera to remove it.
    • Twist the tab clockwise to unlock the door, then pull outward from the camera to remove it.

  3. Remove the battery from inside the battery housing and set the cover aside.
    • Remove the battery from inside the battery housing and set the cover aside.

  4. Remove the two 6.4mm screws above the lens aperture using a phillips #00 screw driver.
    • Remove the two 6.4mm screws above the lens aperture using a phillips #00 screw driver.

  5. Remove the 6.4mm screw from the inside of the flash bezel.
    • Remove the 6.4mm screw from the inside of the flash bezel.

  6. kits de reparo de baterias de iPhone

    Only $29.99

    Buy Now

    kits de reparo de baterias de iPhone

    Only $29.99

    Buy Now
  7. Flip the camera upside down and remove the 5.4mm screw below the lens bezel on the front of the camera.
    • Flip the camera upside down and remove the 5.4mm screw below the lens bezel on the front of the camera.

  8. Remove the 5.6mm screws behind the battery cover.
    • Remove the 5.6mm screws behind the battery cover.

  9. Remove two 6.4mm screws on the latch mechanism on the right side of the camera.
    • Remove two 6.4mm screws on the latch mechanism on the right side of the camera.

  10. Remove the 6.4mm screw on the top of the inside edge of the battery hole.
    • Remove the 6.4mm screw on the top of the inside edge of the battery hole.

  11. Starting at the flash, carefully pull the front cover away from the camera. Starting at the flash, carefully pull the front cover away from the camera.
    • Starting at the flash, carefully pull the front cover away from the camera.

  12. Remove the 4.3mm screw below the camera strap ring.
    • Remove the 4.3mm screw below the camera strap ring.

  13. Remove two 4.8mm screws located on both sides of the eyepiece.
    • Remove two 4.8mm screws located on both sides of the eyepiece.

  14. Pull the top cover up slowly.
    • Pull the top cover up slowly.

    • A ribbon cable is attached to the bottom of the top cover and the camera. Pull up very carefully to avoid damaging this.

  15. Once you have revealed the ribbon cable, gently let the top cover hang off the front of the camera. Use the plastic opening tool to gently pull the white tabs on the ribbon cable, releasing the ribbon cable.
    • Once you have revealed the ribbon cable, gently let the top cover hang off the front of the camera. Use the plastic opening tool to gently pull the white tabs on the ribbon cable, releasing the ribbon cable.

    • If you pull the white tabs all the way out, just insert them back in to avoid losing them.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Mark

Membro desde: 20-04-2011

93 reputação

5 Guias de autoria

Equipe

Cal Poly, Team 8-9, Regan Spring 2011 Membro de Cal Poly, Team 8-9, Regan Spring 2011

CPSU-REGAN-S11S8G9

4 Membros

6 Guias de autoria

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 2

Últimos 30 dias: 8

Todo: 3,177