Wiki contribuído por estudante
Uma equipe incrível de estudantes do nosso programa de educação fez esta wiki.
The sun lamp will not turn on
The sun lamp will not illuminate when the ON/OFF button is pushed. Look below for a number of issues that could be the cause.
Battery Issues
In order to isolate the battery, turn the lantern ‘’LED side down’’. Remove the two screws found at each end of the device. The orange casing will easily lift off of the rest of the device. Once the device is separated, locate the battery. The battery will say ‘’Lithium-ion Battery Pack’’.
Drained/Dead Battery
Check to make sure that the battery is not drained or dead. Allow the sun lamp appropriate amount of time to charge in a well-lit area. If the battery will no longer charge, the battery may need to be replaced.
If you have one available, you could also test the voltage of the battery with a multimeter to see if the battery is dead. Check out this multimeter device page for more information.
Click here for a guide to replacing the battery.
Disconnected Battery
Check to make sure that the battery is properly connected to the device. One red wire and one black wire connect the battery to the device. Firmly press downwards on white clip to ensure that a good connection is made.
Click here for a guide to reconnect the battery.
Solar Panel Issues
If the solar panel is not allowing the device to charge, there is an issue with the panel itself or the charging cable.
First, inspect the charging cable for damage. If there is no visible damage to the exterior charging cable, follow it to a black plastic box on the back of the solar panel. Open the box by sliding the lid of the box in the direction indicated by the downward arrow printed on the lid. Once the lid is off, check the internal wires for damage. Damage indicates that the cable is not properly connected to the solar panel and will need to be replaced.
If the charging cable is working properly, you will need to replace the solar panel component. Cracked or damaged solar panels will also need to be replaced.
The wrist strap is no longer attached
If the wrist strap is no longer attached, the first issue may be that it has been seated wrong after opening the case. This can be solved by re-seating the wrist strap.To properly seat the wrist strap, open the case and on both sides perpendicular to the screws, there are two molded rectangular holes. Each end of the wrist strap sits in the holes closest to the edge of the case.
Another issue may be that the wrist strap has broken, if so, the wrist strap will need to be replaced.
Click here for a guide to replace the wrist strap.
Lamp is not as bright as it once was
Burnt out LED
If the Sun King Solar Lamp is not as bright as expected, check to make sure that all of the LED lights are working properly. Burnt out bulbs will prevent the lamp from illuminating even if the rest of the device is working properly. If the LED lights are burnt out, then the LED circuit board will need to be replaced.
Moisture in the device
Inspect the case of the sun king solar lamp. If there is moisture or a fog around the LEDs, open the case and wipe down the clear cover with a dry soft cloth. Before putting the lamp back together, inspect the O-ring and make sure that it is properly seated. If this O-ring is not seated properly, then moisture is allowed to enter the case near the LEDs.
If the Sun King Solar Lamp is foggy in the area without the LEDs open the case and wipe the moisture out with a dry soft cloth. Inspect the rubber mounts for the stand and make sure that these are damage free and seated properly. This would be the cause of moisture in this area.
Click here for a guide to cleaning the lamp housing.
Click here for a guide to replace damaged seals.
Equipe
Michigan Tech, Team 1-3, Lauer Fall 2014 Membro de Michigan Tech, Team 1-3, Lauer Fall 2014
MTU-LAUER-F14S1G3
Membros da 3
Autoria de 5 guias
16 comentários
i have solar king Solo Solar emergency light.. some day ago my light is automatically start. now i am trying to start it but it can not start.. battery is in good condition. when i charge in sun light charging light is blinking.. how can i solve this problem... is that any problem with PCB..... ????
mackshinde007 - Responder
What if it's not charging?
Godwin Idewa - Responder
I think that the problem of '''solar lights''' is because there are a lot of parts and components, some technologies are not closed, and some use fake materials.
Bluntzhou - Responder
What if the solar is charging but no out put whay might be the problem
Jim Njeri - Responder
My sun king solar greenlight is not working and the battery is full and also the connections are done properly. What could be the problem with it
Dennis mulwa - Responder
I used my sun king solar to charge my phone then I slept off. When I woke up, I put it on, the light came on but it's not reflecting any battery percentage. What does this mean please?
Quinn Knight - Responder
My Solar 'system does not supply POWER ..I mean NO OUTPUT BUT IT CHARGES WHAT IS THE PROBLEM ?
Mlawa Herry - Responder
My sun king solar greenlights are not working you can't even see how far the battery has been changed but everything is working fine
Mwaba Chikuwe - Responder
One of the hanging bulb wire mistakenly cuts in my hand, and I just got the light, and I have been trying to join the wire but the bulb isn't working. Please what should I do
mariam abdulfatai - Responder
My battery is only showing green light from solar charge full but battery light is off for days and not charging. What could be the problem?
Floridah Sikwese - Responder
What can I do when my sunking solar refuses to charger my phone and display something like 03 on the surface?
eleshomichealtemitope - Responder
Can I get the meaning of E7, because it's been displaying that since 2days now and how I can fixed it.
Ibrahim Ishaku - Responder
If your sun lamp is not turning on, there could be several reasons why this is happening. Here are a few steps you can take to try and diagnose the issue:
Check the power source: Make sure your lamp is plugged into a working outlet and that the outlet is receiving power. If the outlet is controlled by a light switch, make sure the switch is turned on.
Check the bulb: Make sure the bulb in your lamp is securely screwed in and not burned out. If the bulb is not making a connection or has burned out, it will need to be replaced.
Check the switch: If the power source and bulb are working properly, the issue may be with the switch. Make sure the switch is in the "on" position and is functioning properly.
Check the wiring: If the above steps do not solve the issue, it may be a problem with the wiring. This can be a more complicated issue and may require professional repairs.
But if you have faced charging problems then click here to read the complete details of Charging Solar Lights the First Time.
Muhammad Sami - Responder
My sun king solar greenlight is not working and the battery is full and also the connections are done properly. What could be the problem?. It displayed E-7 error code. No output supply
Kgb - Responder
My battery stopped indicating when it's charging what could be the problem
Francis Oduori - Responder
I just bought sun king TV couple of days ago and I was using it before it went off. It was movie I installed in my flash but as it went off it shows the flash but cannot display the content on in the flash what do I do now pls?
Lukason - Responder