Menu

Suas configurações

Minha bancada de trabalho

Ganhe acesso rapidamente a guias, partes e respostas para seus dispositivos
Carrinho

Parece que seu carrinho de compras está vazio

Visite Nossa Loja

VicTsing MM057 2.4G Wireless Mouse Teardown

Escrito Por: Neil (e outro colaborador)
Publicado em: March 6, 2018
  • Comentários: 1
  • Favoritos: 1
  • Visualizações: 1,3k

Teardown

Ferramentas utilizadas neste teardown

Comprar estas ferramentas

Introdução

This guide shows the steps required to fully disassemble the VicTsing MM057 wireless mouse.

Este teardown (desmontagem analítica) não é um guia de reparo. Para reparar seu/sua VicTsing MM057 2.4G Wireless Mouse, use o nosso manual de serviço.

  1. The VicTsing MM057 2.4G Wireless Mouse.

    • The VicTsing MM057 2.4G Wireless Mouse.

    Editar

  2. Filp over and remove battery cover and USB dongle.

    • Filp over and remove battery cover and USB dongle.

    • Mouse

    • USB dongle

    • Battery cover

    Editar

  3. Remove three screws. Two screws are located under the adhesive pads closer to the front of the mouse. The third screw is under the battery cover.

    • Remove three screws. Two screws are located under the adhesive pads closer to the front of the mouse. The third screw is under the battery cover.

    • Screw locations

    Editar

  4. Gently pull apart the enclose. Be wary of the board-to-board connector cables.

    • Gently pull apart the enclose. Be wary of the board-to-board connector cables.

    • Board-to-board receptacle

    Editar

  6. Disconnect the board-to-board cables by squeezing the sides of the receptacles on base.

    • Disconnect the board-to-board cables by squeezing the sides of the receptacles on base.

    • Top

    • Base

    Editar

  7. Separate battery connection wires from the base chassis and remove the base circuit board and optical lens.

    • Separate battery connection wires from the base chassis and remove the base circuit board and optical lens.

    • Base circuit board

    • Optical lens

    • Base chassis

    Editar

  8. Remove the scroll wheel.

    • Remove the scroll wheel.

    • Scroll wheel

    • From top to bottom: right click, wheel click, wheel rotary encoder, and left click actuators

    • Crystal oscillator (12 MHz)

    • From left to right: optical receiver and red LED

    Editar

  9. Underside of base circuit board.

    • Underside of base circuit board.

    • Microcontroller (epoxy coated)

    • Bluetooth antenna

    • Optical receiver (bottom side)

    Editar

  10. Remove screw from center of top circuit board.

    • Remove screw from center of top circuit board.

    • Screw location

    Editar

  11. Separate top circuit board from the top chassis.

    • Separate top circuit board from the top chassis.

    • Top chassis

    • Top circuit board

    Editar

  12. Mode selector button

    • Mode selector button

    • Side buttons

    • LED status indicator

    Editar

Autor

com 1 outro contribuidor

Neil

Membro desde: 06-03-2018

203 reputação

Autoria de 1 guia

Emblemas: 0

Um comentário

Adicionar um comentário

This is a nice guide keep up the good work!!!!

Damon Diller - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 3

Últimos 7 dias: 18

Últimos 30 dias: 85

Todo: 1,371