Introdução

Complete teardown of Sidekick II

This teardown is not a repair guide. To repair your Sidekick II, use our service manual.

Use the plastic opening tool to remove the 4 buttons on each corner of the Sidekick.
  • Use the plastic opening tool to remove the 4 buttons on each corner of the Sidekick.

  • Gently pry open button and remove button.

  • Do this for each of the 3 buttons remaining.

Adicionar comentário

The bumpers on the top and bottom of the phone can be removed by simply "peeling" them off. The bumpers on the top and bottom of the phone can be removed by simply "peeling" them off.
  • The bumpers on the top and bottom of the phone can be removed by simply "peeling" them off.

Adicionar comentário

Use the Phillips head screwdriver to remove the 4 screws that are underneath the 4 buttons you removed in step one.
  • Use the Phillips head screwdriver to remove the 4 screws that are underneath the 4 buttons you removed in step one.

Adicionar comentário

Flip the screen up halfway (90 degrees), to reveal the 2 screws above the right side of the keyboard.
  • Flip the screen up halfway (90 degrees), to reveal the 2 screws above the right side of the keyboard.

  • Use the Torx 6 screwdriver to remove these 2 screws.

  • Be careful in handling the phone after removing the screws, because the two main bodies of the phone are no longer attached.

Adicionar comentário

After removing the 6 screws and both bumpers, the phone will be easy to separate into the two main bodies.
  • After removing the 6 screws and both bumpers, the phone will be easy to separate into the two main bodies.

  • You can use your hands to simply pull apart the top casing from the bottom casing.

Adicionar comentário

MANTA DRIVER KIT
112 bit driver kit $59.99
MANTA DRIVER KIT
112 bit driver kit $59.99
Remove screen from casing. Remove screen from casing.
  • Remove screen from casing.

Adicionar comentário

Remove 4 screws from back of screen using Torx 6 Screwdriver. Pry screen out of casing using fingers.
  • Remove 4 screws from back of screen using Torx 6 Screwdriver.

  • Pry screen out of casing using fingers.

Adicionar comentário

Remove 4 screws from front of screen with Phillip screwdrivers. Peel off the metal covering on the back of the screen. Be careful when taking off the metal covering. The orange ribbon will not come out all the way, and it is fragile.
  • Remove 4 screws from front of screen with Phillip screwdrivers.

  • Peel off the metal covering on the back of the screen.

  • Be careful when taking off the metal covering. The orange ribbon will not come out all the way, and it is fragile.

Adicionar comentário

Remove the protective cover in front of the screen.
  • Remove the protective cover in front of the screen.

  • Do not use metal tools, you may damage the protective cover or the screen. Use your fingers only.

Adicionar comentário

Take the screws out using the Torx 6 screwdriver. Then lift the thumb wheel and housing off of the front panel.
  • Take the screws out using the Torx 6 screwdriver.

  • Then lift the thumb wheel and housing off of the front panel.

Adicionar comentário

Remove 2 black "rivets" from back of casing with the plastic opening tool. Press keyboard out of front of casing using thumbs.  Don't press too hard as you may break the board.
  • Remove 2 black "rivets" from back of casing with the plastic opening tool.

  • Press keyboard out of front of casing using thumbs. Don't press too hard as you may break the board.

Adicionar comentário

Remove the 5 black screws with a Phillips head screwdriver. Lift the bottom of the control board from housing, and separate the two.
  • Remove the 5 black screws with a Phillips head screwdriver.

  • Lift the bottom of the control board from housing, and separate the two.

Adicionar comentário

Carefully remove battery and back plate.
  • Carefully remove battery and back plate.

  • Do not use metal tools, you may damage the control board. Use only your fingers.

Adicionar comentário

Here are all of the pieces that you have disassembled
  • Here are all of the pieces that you have disassembled

Adicionar comentário

michael albaum

Member since: 20-01-2010

45 reputação

11 Guides authored

Equipe

Cal Poly, Team 3-19, Maness Winter 2010 Membro de Cal Poly, Team 3-19, Maness Winter 2010

CPSU-MANESS-W10S3G19

4 Membros

11 Guides authored

nice job from a former geek

Jared Boies - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 2

Últimos 30 dias: 6

Todo: 6,362