Pular para o conteúdo principal

Ferramentas utilizadas neste teardown

Este teardown (desmontagem analítica) não é um guia de reparo. Para reparar seu/sua Scotch TL901, use o nosso manual de serviço.

  1. The Scotch TL901 Laminator
    • The Scotch TL901 Laminator

  2. Using a small Phillips screwdriver, remove the screws from the bottom of the plastic case.
    • Using a small Phillips screwdriver, remove the screws from the bottom of the plastic case.

    • Rubber feet in the four corners must be removed first to gain access to the screws underneath. A sticker may also be covering the middle screw on the left.

  3. Pull off the silver plastic cover and gain access to the internal components.
    • Pull off the silver plastic cover and gain access to the internal components.

    • The rollers, motor, circuit board, and LEDs are all visible now.

  4. First unplug all three wire headers connected to the circuit board.
    • First unplug all three wire headers connected to the circuit board.

    • Unscrew the two screws holding down the circuit board by its corners and remove the board from the laminator.

  5. Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora

    Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora
  6. Unhook the spring from the plastic surrounding the motor.
    • Unhook the spring from the plastic surrounding the motor.

  7. Hold the roller enclosure from both sides, indicated by the markers, and pull upwards and slightly out.
    • Hold the roller enclosure from both sides, indicated by the markers, and pull upwards and slightly out.

    • Free access to the motor and rollers is now possible.

  8. Remove the motor from the rollers by unscrewing the three screws holding them together.
    • Remove the motor from the rollers by unscrewing the three screws holding them together.

  9. Remove the sensor from the roller enclosure by unscrewing the two spring-loaded screws.
    • Remove the sensor from the roller enclosure by unscrewing the two spring-loaded screws.

  10. Unscrew the two screws and the bar on the other.
    • Unscrew the two screws and the bar on the other.

  11. Pull the black washers sideways off the metal rod of the roller.
    • Pull the black washers sideways off the metal rod of the roller.

    • Pull the gears off.

  12. With the gears off, the plastic panel falls off and the rollers come out of the enclosure. The laminator is now disassembled.
    • With the gears off, the plastic panel falls off and the rollers come out of the enclosure.

    • The laminator is now disassembled.

Calvin Xu

Membro desde: 18-04-2013

190 reputação

Autoria de 1 guia

Equipe

F14BraunReverseEng Membro de F14BraunReverseEng

Community

2 Membros

8 Guias de autoria

Why is the screw on the left side so hard to get out?

Teri L Geist - Responder

Thank you..

Putting it back together is more of a challenge.

Frank - Responder

You're right Frank. For me, getting it to stay together after the tear down and reassembly required superglue and two extra screws. ;) But at least it's working again. Thanks for the great instructions.

pjcall975 - Responder

Thank you! Just needed to open and remove a jam. Followed your guide and all is well.

KQuinn

Kate Quinn - Responder

Thank you for posting these instructions. I was able to remove a quarter that got trapped inside.

seanretzloff - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 12

Últimos 7 dias: 55

Últimos 30 dias: 241

Todo: 18,023