Unibody 8x SATA SuperDrive (Pre-Mid 2009)

  • Unibody 8x SATA SuperDrive (Pre-Mid 2009) / Used
Unibody 8x SATA SuperDrive (Pre-Mid 2009)

Condição: Usado

US$ 49,99

US$ 49,99

Enviaremos uma mensagem quando o produto estiver disponível em estoque.

Detalhes do produto

Descrição

Descrição

Replace a damaged or malfunctioning dual-layer SATA drive.

Compatibilidade

Compatibilidade

  • All 13" Unibody MacBooks (Model A1278)
  • Late 2008 or Early 2009 Unibody 15" MacBook Pros
  • Early or Mid 2009 Unibody 17" MacBook Pros

Especificações

Especificações

Part #:
661-5147
Speed:
8x DVD-R write
4x DVD-RW write
8x DVD+R write
4x DVD+RW write
4x DVD+R (DL) write
24x CD-R write
10x CD-RW write
8x DVD read
24x CD read

Compatibilidade

MacBook Pro 15" Unibody Late 2008 & Early 2009
2.4 GHz
2.53 GHz
2.66 GHz
2.8 GHz
2.93 GHz
MacBook Pro 17" Unibody
2.66 GHz (Early 2009)
2.8 GHz (Mid 2009)
2.93 GHz (Early 2009)
3.06 GHz (Mid 2009)
MacBook Unibody A1278
2 GHz
2.4 GHz

Histórias de Reparos

Avatar do usuário
Sondre Selnes's Story Photo #257497

Meu Problema

The fan on my MacBook Pro was reaching its end. It was terrible noisy ! I was in the middle of a programming project for the iPhone and making video guide for the new software, when the fan of my computer broke down. I had to stop all recording (Big Blue Yeti mic, ScreenFlow recording...).

Minha Solução

The vi . . .

Avatar do usuário

Meu Problema

Old drive was becoming unreliable

Minha Solução

Instructions were spot on.

Meu Conselho

Tweezers are a must on this repair. The small screws are easy to remove but the bulk of the time is spent replacing them when you do not use tweezers. I used a plastic knife rather than a spudger. Worked just fine.

Avatar do usuário

Meu Problema

Fan bearing started getting noisy and then fan started to be slow/intermittent causing overheat shutdown of the MacBook.

Minha Solução

Watched your video to see what I was in for. Seemed relatively straightforward. Opened up the case and got to the fan. 2 of the 3 Philips screws came out easy. One was REALLY torqu . . .

Avatar do usuário

Meu Problema

The old fan had worn out bearings which caused lots of noise and bad performance.

Minha Solução

The switch went well. Took about 30 minutes because the screws were stripped. The comments were very helpful.

Meu Conselho

If the screws are stripped, take a similar size flat screwdriver and put at 45 degrees into the screw so the s . . .

Avatar do usuário

Meu Problema

CPU temperatures had started to spike on my laptop (80C or higher) while doing mundane things at low percentages of CPU, and fan didn't spin up to cool the machine. Apple did diagnostics, said all was well. Temperature Gauge Pro detected a problem with fan, however, so I ordered a replacement to s . . .

Avatar do usuário

Meu Problema

Loud noises prompted me to take my Macbook Pro to the Genius Bar. They wanted to keep it for 3+ days to replace the fan, at a pretty significant cost. I happen to be blessed with a very smart teenager who cut his teeth on taking Mac's apart. Quick order on iFixit, an even faster delivery, and voi . . .

Avatar do usuário

Meu Problema

battery only lasted about an hour fully charged, and it the whole computer would rapidly overheat.

Minha Solução

A bit scary. The battery went in without a hitch, but when removing the old fan, the socket ripped off of the circuit board. I ended up soldering the individual wires back on. Now it works great though! . . .

Avatar do usuário

Meu Problema

The old fan had become noisy - bearings worn out probably. (After taking it out, I could see the blades spun crooked.)

Minha Solução

Pretty easy repair, only 3 internal screws. The connector is a little tricky since it's so small, you tend to think you're gonna break it. Go slowly around the edges and it'll com . . .

Avatar do usuário

Meu Problema

My fan was making a god awful sound whenever my macbook would start heating up. This had been happening ever since an unfortunate crepe experience where I managed to spill lemon-sugar syrup into my keyboard.

Minha Solução

The repair was incredibly straight forward. It was a very minimal risk procedure.

Meu Conselho

Be prepared . . .

Avatar do usuário

Meu Problema

The blades on the original fan had broken and was making a lot of noise when it spun up.

Minha Solução

I've opened the computer many times before so the repair was a piece of cake. ~5 minutes in total.

Meu Conselho

-

Mostrar mais