Este produto não está disponível no seu país.
código do item: IF161-102-2
Este produto não está disponível no seu país.
US$ 89,99
Em promoção
Peças usadas do estoque A estão em excelente estado
Peças de estoque B possuem leves marcas de uso
Peças de estoque C possuem marcas profundas de uso, mas ainda funcionam plenamente
US$ 89,99
Em promoção
Fora de estoque
Pronto para Envio
Fora de estoque
Enviaremos uma mensagem quando o produto estiver disponível em estoque.
Não temos muito estoque disponível
Detalhes do produto
Descrição
Descrição
Replace a scratched or malfunctioning trackpad compatible with a Late 2008 or Early 2009 model MacBook Pro 15" Unibody.
Compatibilidade
Compatibilidade
Especificações
Especificações
Compatibilidade
MacBook Pro 15" Unibody Late 2008 & Early 2009
|
|
Histórias de Reparos
Dropped a paperweight on my trackpad and shattered it. It's an old machine so I considered not fixing it, but it wasn't until I plugged a mouse in and started using it that I realized how second nature the trackpad use and gestures had become.
The repair went fine, no issues. It took about 2 hours all told, but much of that was my preparation and reading each step several times before proceeding. The trackpad is buried in the machine, so the whole thing has to come apart.
A couple notes:
- You will be removing over 40 very small, non-interchangeable screws. Be prepared for this. I used the paper + scotch tape method, as pictured, but do whatever is comfortable. Just DON'T put them all in a pile.
- Directions call for #00 phillips, but I felt this cammed out too easily and could have caused the screws to strip. I used the #000 without any issues.
- Directions also call for just the screwdriver and spudger, but you should have tweezers on hand to help handle the screws.
- the hardest part by far will be handling the connections to the logic board. These are very tiny, very delicate connections and if you break any of them you are in trouble. PAY ATTENTION TO WHICH DIRECTION YOU NEED TO PULL IN.
Not mentioned in the directions: there is some wiggle room when replacing the trackpad. Because the machine is set up on its side for this step, my trackpad is slightly off center (see picture). Had I realized that there was room, I would have taken a second and centered it before tightening the 6 screws that hold the trackpad in place. This is purely aesthetic, but I saw it as soon as I turned the laptop rightside up again.
Also, potentially related: after I restarted the machine, I had a runaway process called rpcsvchost using 100% of my CPU, and I had to reset my PRAM to fix it. I don't know it that's related or coincidence.
Dropped a paperweight on my trackpad and shattered it. It's an old machine so I considered not fixing it, but it wasn't until I plugged a mouse in and started using it that I realized how second nature the trackpad use and gestures had become.
The repair went fine, no issues. It took about 2 hours al . . .
The Trackpad was broken.
Following the iFixit-Repair-Guide step-by-step the repair was successful.
No.
The trackpad apparently doesn't like water (even a drop of condensation from a glass), so it needed to be replaced. Soon. Don't like using a mouse anymore.....
The repair went great, the second time! After reassembly the first time, the MBP wouldn't power on, so I disassembled and reassembled again, making sure all the tiny, tiny cables were snug. After that, all was well!
My only advice is just the standard stuff: make sure you have plenty of light, plenty of space to work (including room to lay out the screws next to you in the same pattern you removed them) and make sure the dogs can't get to your workspace to sniff around and rearrange the tiny parts!
The trackpad apparently doesn't like water (even a drop of condensation from a glass), so it needed to be replaced. Soon. Don't like using a mouse anymore.....
The repair went great, the second time! After reassembly the first time, the MBP wouldn't power on, so I disassembled and reassembled agai . . .
Produtos destacados
