Ir para o conteúdo principal
Inglês
Chinês

如何更换三星 Galaxy S 系列手机客制化胶带

Guia de informações

= Concluído = Incompleto
How To Replace Custom-cut Adhesive For Galaxy SSamsung Phones
Learn how to install the adhesive for glass-backed Samsung's Galaxy S phones. Also includes instructions for back cover component adhesives.
    Not sure what to do with all the adhesive strips in your back cover kit? You’ve come to the right place! This guide shows how to use the back cover adhesive kit for the Galaxy S seriesphones with glass backs (S7 and newer). It also includes instructions on how to transfer and install various back cover components, such as the rear bezel and fingerprint sensor.
    ''You may not need to use all the adhesive strips included in the kit.'' If you are transferring the fingerprint sensor, you may need some double-sided tape such as Tesa tape.
    For a list of adhesive strips for the Galaxy S phone, [link|https://www.ifixit.com/Store/Parts/Samsung-Galaxy-S-Series/Adhesive_Strips|follow this link].
    When applying adhesive strips like these, here are some general tips:
    * Generally, adhesives strips have a colored side and a non-colored (paper or clear plastic) side. '''***The non-colored side determines which surface the strip should be applied to first.'''***
    * To make adhesive application easier, you can align an unexposed strip to its intended position on the phone, then [link|https://d3nevzfk7ii3be.cloudfront.net/igi/a6EfdSi3YTRDsMVw.large|tape one edge down to hold the strip in place]. This will allow you to peel away the plastic liners and expose the adhesive without losing alignment.

      Descreva a peça ou componente específico deste(a) device em que você está trabalhando. Ex: Bateria

      Criar um título.

      Este breve resumo só aparecerá em resultados de pesquisas.

      Dar informações básicas antes de o leitor mergulhar no guia.

      Passos do guia

      Passo 1

      根据你的手机型号,你可能不需要完成本指南的某些部分。检查你的粘合剂套装,看需要做什么:

      Passo 2 — 指纹传感器和垫圈

      以下三个步骤显示了如何卸下和转移指纹传感器及其垫圈。

      Passo 3

      如果仅更换指纹传感器而不是指纹传感器垫片,请跳过此步骤。

      Passo 4

      要将指纹传感器固定到新的后盖上,请使用自定义的切割胶,或将传感器的周边用双面胶带(例如Tesa胶带)排列。

      Passo 5 — 后挡板

      以下四个步骤显示了如何卸下和转移后挡板。挡板支持后置摄像头,闪光灯和指纹传感器(某些型号)。

      Passo 6

      卸下挡板。

      Passo 7

      剥下边框胶条上的透明塑料衬垫,以露出胶粘剂。

      Passo 8

      小心地将边框对准并放在粘合剂上。

      Passo 9 — 后盖支撑胶

      以下四个步骤显示了如何安装后盖支撑胶。

      Passo 10

      将透明衬板从支撑胶条上剥离下来以露出胶粘剂。

      Passo 11

      将后盖小心地放到裸露的支撑条上。这样可以确保将胶粘剂以适当的位置转移到后盖上。

      Passo 12

      卸下后盖。

      Passo 13 — 周边胶

      其余步骤显示了如何安装后盖周边胶粘剂。

      Passo 14

      从外围胶粘带上剥离透明衬垫,以露出胶粘剂。

      Passo 15

      要密封手机,请对齐后盖并将其放在手机框架上。

      Suas contribuições são licenciadas pela licença de código aberto Creative Commons.