Ir para o conteúdo principal

Este guia tem alterações mais recentes. Mudar para a última versão não verificada.

iRobot Roomba 551 Bumper Sensor Replacement

O que você precisa

  1. iRobot Roomba 551 Bumper Sensor Replacement, Side Brush: passo 1, imagem 1 %32
    • Place your Roomba upside-down on a hard surface.

  2. iRobot Roomba 551 Bumper Sensor Replacement: passo 2, imagem 1 %32
    • While holding the side brush in place, use a Phillips #1 screwdriver to remove the 4.5mm screw from the center of the brush.

  3. iRobot Roomba 551 Bumper Sensor Replacement: passo 3, imagem 1 %32
    • Gently pull upwards on the brush to remove it.

  4. iRobot Roomba 551 Bumper Sensor Replacement, Bottom Plate: passo 4, imagem 1 %32
    • Rotate the Roomba upside-down so the bottom is facing towards you.

  5. iRobot Roomba 551 Bumper Sensor Replacement: passo 5, imagem 1 %32 iRobot Roomba 551 Bumper Sensor Replacement: passo 5, imagem 2 %32
    • Using a Phillips #2 screwdriver, remove the captive screws that hold the bottom plate in place.

  6. iRobot Roomba 551 Bumper Sensor Replacement: passo 6, imagem 1 %32
    • Carefully lift the bottom plate.

    • The battery is only secured in place by the bottom plate, and may fall out once the bottom plate is removed.

  7. iRobot Roomba 551 Bumper Sensor Replacement, Bumper: passo 7, imagem 1 %32 iRobot Roomba 551 Bumper Sensor Replacement, Bumper: passo 7, imagem 2 %32 iRobot Roomba 551 Bumper Sensor Replacement, Bumper: passo 7, imagem 3 %32
    • With a Phillips #1 screwdriver, remove the ten 12mm screws located along the bottom of the bumper.

  8. iRobot Roomba 551 Bumper Sensor Replacement: passo 8, imagem 1 %32
    • Lift the bottom cover and set it to the side.

  9. iRobot Roomba 551 Bumper Sensor Replacement: passo 9, imagem 1 %32 iRobot Roomba 551 Bumper Sensor Replacement: passo 9, imagem 2 %32
    • Flip the Roomba over, grasp the bumper, and gently lift to remove.

    • The battery is not secured in place once the bottom plate has been removed, and may fall out when the Roomba is turned right-side up.

  10. iRobot Roomba 551 Bumper Sensor Replacement, Bumper Sensor: passo 10, imagem 1 %32
    • Flip the Roomba so that the bottom is facing you.

  11. iRobot Roomba 551 Bumper Sensor Replacement: passo 11, imagem 1 %32 iRobot Roomba 551 Bumper Sensor Replacement: passo 11, imagem 2 %32
    • Remove the two 5mm screws located near the center of the bumper using a Phillips #1 screwdriver.

  12. iRobot Roomba 551 Bumper Sensor Replacement: passo 12, imagem 1 %32
    • Pull gently on the bottom of the sensor to remove.

  13. iRobot Roomba 551 Bumper Sensor Replacement: passo 13, imagem 1 %32 iRobot Roomba 551 Bumper Sensor Replacement: passo 13, imagem 2 %32 iRobot Roomba 551 Bumper Sensor Replacement: passo 13, imagem 3 %32
    • Flip the bumper over and lift the sensor from its compartment.

    • You are now free to replace the bumper sensor.

Conclusão

To reassemble your device, follow these instructions in reverse order.

4 outras pessoas executaram este guia.

Cody Rhoads

Membro desde: 01/16/14

348 Reputação

Autoria de 2 guias

Equipe

Cal Poly, Team 13-14, Regan Winter 2014 Membro de Cal Poly, Team 13-14, Regan Winter 2014

CPSU-REGAN-W14S13G14

Membros da 4

Autoria de 19 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 2

Últimos 30 dias: 5

Duração total: 4,651