Menu

Suas configurações

Minha bancada de trabalho

Ganhe acesso rapidamente a guias, partes e respostas para seus dispositivos
Carrinho

Parece que seu carrinho de compras está vazio

Visite Nossa Loja

iPhone 7 Logic Board Disconnection

Escrito Por: Evan Noronha (e 3 outros contribuidores)
  • Comentários: 8
  • Favoritos: 0

Dificuldade

Moderado

Passos

13

Tempo necessário

Sugerir um tempo??

Seções

1

Sinalizadores

1

Prerequisite Only

Pré-requisito somente

Por favor, note que este guia é apenas um pré-requisito para outros guias.

Introdução

prereq only

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

  1. Use the flat end of a spudger to disconnect the rear-facing camera connector. Use the flat end of a spudger to disconnect the rear-facing camera connector.

    • Use the flat end of a spudger to disconnect the rear-facing camera connector.

    Editar

  2. Remove the following Phillips screws securing the rear camera bracket to the rear case: One 1.3 mm screw

    • Remove the following Phillips screws securing the rear camera bracket to the rear case:

    • One 1.3 mm screw

    • One 2.5 mm screw

    Editar

  3. Remove the bracket.

    • Remove the bracket.

    Editar

  4. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module. Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

    • Use the pointed end of a spudger to pry up and disconnect the antenna bus connector, just left of the rear camera module.

    Editar

  5. Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

    • Remove the two 1.2 mm tri-point screws securing the upper cable bracket.

    Editar

  6. PC Laptop Batteries

    An easy fix for a big power boost.

    Comprar agora

    PC Laptop Batteries

    An easy fix for a big power boost.

    Comprar agora

  7. Remove the upper cable bracket. Remove the upper cable bracket.

    • Remove the upper cable bracket.

    Editar

  8. Use the flat end of a spudger to disconnect the upper cable connector. Use the flat end of a spudger to disconnect the upper cable connector.

    • Use the flat end of a spudger to disconnect the upper cable connector.

    Editar

  9. Remove the Phillips screws securing the Wi-Fi antenna: Three 1.2 mm screws

    • Remove the Phillips screws securing the Wi-Fi antenna:

    • Three 1.2 mm screws

    • One 1.7 mm screw

    Editar

  10. Remove the top left antenna. Remove the top left antenna.

    • Remove the top left antenna.

    Editar

  11. Remove the following Phillips screws:

    • Remove the following Phillips screws:

    • One 1.3 mm screw

    • One 2.2 mm screw

    Editar

  12. Remove the bracket. Remove the bracket.

    • Remove the bracket.

    Editar

  13. Remove the 2.2 mm standoff screw from the grounding bracket.

    • Remove the 2.2 mm standoff screw from the grounding bracket.

    • Standoff screws are best removed using an iPhone Standoff Screwdriver Bit and driver handle.

    • In a pinch, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

    Editar

  14. Use tweezers to gently bend the logic board grounding bracket out of the way. Use tweezers to gently bend the logic board grounding bracket out of the way.

    • Use tweezers to gently bend the logic board grounding bracket out of the way.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor

com 3 outros contribuidores

Evan Noronha

Membro desde: 05-02-2015

171.668 reputação

177 Guias de autoria

Emblemas: 49

+46 emblemas

Equipe

iFixit Membro de iFixit

Community

99 Membros

9.305 Guias de autoria

0 comentários

Adicionar um comentário

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Todo: 86