Conserte seus objetos Comunidade Loja

iPhone 6s Plus Speaker Replacement

Pré-requisito somente
Este guia destina-se apenas a ser usado como pré-requisito para outros guias. É incompleto por si só.

Introdução

Prerequisite guide only! Speaker module replacement for the iPhone 6s Plus. Updated version which contains photos that have the logic board intact.

O que você precisa

  1. iPhone 6s Plus Speaker Replacement, Speaker: passo 1, imagem 1 %32 iPhone 6s Plus Speaker Replacement, Speaker: passo 1, imagem 2 %32

    • Use the point of a spudger to pry up and disconnect the antenna cable from the bottom of the logic board.

    Editar

  2. iPhone 6s Plus Speaker Replacement: passo 2, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 2, imagem 2 %32

    • Use the point of a spudger to pry up and disconnect the Lightning connector cable from the logic board.

    Editar

  3. iPhone 6s Plus Speaker Replacement: passo 3, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 3, imagem 2 %32

    • Remove the three Phillips screws securing the Lightning connector bracket:

    • Two 3.5 mm screws

    • One 2.7 mm screw

    • Remove the bracket.

    Editar

  5. iPhone 6s Plus Speaker Replacement: passo 4, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 4, imagem 2 %32

    • Use the point of a spudger to pry up and disconnect the antenna cable from the Lightning connector assembly.

    Editar

  6. iPhone 6s Plus Speaker Replacement: passo 5, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 5, imagem 2 %32

    • Use the point of a spudger to pry up and disconnect the antenna cable from the top of the logic board.

    Editar

  7. iPhone 6s Plus Speaker Replacement: passo 6, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 6, imagem 2 %32 iPhone 6s Plus Speaker Replacement: passo 6, imagem 3 %32

    • Carefully lift the antenna cable and de-route it from the edge of the phone. Use the point of a spudger to help lift the cable free it from the retaining clips.

    • If the cable does not have enough room to lift up, loosen this Phillips screw securing the logic board so that the board can give more wiggle room.

    • Be sure to re-tighten this screw during re-installation.

    • If the cable snags near the SIM reader, it's likely caught on the SIM tray ejection mechanism. Use the point of a spudger to slide the plastic rod out of the way.

    • During re-installation, be sure to route the antenna cable underneath the logic board corner.

    • During reassembly, you can also re-insert the SIM card tray after re-routing the antenna cable.

    • If you feel any resistance, stop and make sure that the tray isn't snagging the antenna cable.

    Editar

  8. iPhone 6s Plus Speaker Replacement: passo 7, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 7, imagem 2 %32

    • Remove the six Phillips screws securing the speaker to the rear case:

    • One 2.5 mm screw

    • Two 2.7 mm screws

    • One 1.5 mm screw

    • One 1.7 mm screw

    • One 2.6 mm screw securing the speaker to the bottom edge of the rear case.

    Editar

  9. iPhone 6s Plus Speaker Replacement: passo 8, imagem 1 %32 iPhone 6s Plus Speaker Replacement: passo 8, imagem 2 %32 iPhone 6s Plus Speaker Replacement: passo 8, imagem 3 %32

    • Insert the flat end of a spudger between the long edge of the speaker module and the case wall.

    • Pry gently to loosen the speaker module.

    • Once the module is loose, lift and remove the speaker module and the attached antenna cable from the phone.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 1 outro contribuidor

Arthur Shi

Membro desde: 01/03/18

252.474 Reputação

Autoria de 526 guias

Emblemas: 47

+44 outros emblemas

Equipe

iFixit Membro de iFixit

Staff

Membros da 135

Autoria de 16.763 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Duração total: 150