Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
Vídeo de Apresentação
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Power off your iPhone before beginning disassembly.
-
Your iPhone 4 rear cover may have either two #000 Phillips screws or Apple's 5-Point "Pentalobe" screws (second image). Check which screws you have, and ensure you also have the correct screwdriver in order to remove them.
-
Remove the two 3.6 mm Pentalobe or Phillips #000 screws next to the dock connector.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Push the rear panel toward the top edge of the iPhone.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pinch the rear panel with your fingers and lift it away from the iPhone. Alternatively, use a Small Suction Cup .
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.
-
Remove the metal clip covering the antenna connector.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the clear plastic pull tab to gently lift the battery out of the iPhone.
-
If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.
-
Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a SIM card eject tool or a paperclip to eject the SIM card and its holder.
-
Remove the SIM card and its holder.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following two screws:
-
One 1.2 mm Phillips
-
One 1.6 mm Phillips
-
Remove the thin steel dock connector cable cover from the iPhone.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use an iPod opening tool to gently pry the dock cable connector up off the logic board from both short ends of the connector.
-
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a plastic opening tool to pry the lower antenna connector up off its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the 1.9 mm Phillips screw securing the bottom of the logic board to the inner case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following five screws securing the Wi-Fi antenna to the logic board:
-
One 2.3 mm Phillips
-
Two 1.6 mm Phillips
-
One 1.4 mm Phillips
-
One 4.8 mm Phillips
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use an iPod opening tool to slightly lift the top edge of the Wi-Fi antenna away from the logic board.
-
Use the tip of a spudger to pull the Wi-Fi retaining clips away from the inner frame.
-
Remove the Wi-Fi antenna from the iPhone. Make sure you don't lose the metal clips on the top of the cover where the 4.8mm screw attaches or the 4.8mm screw. That's the primary reason for abnormal Wi-Fi performance after the reassembly.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use an iPod opening tool to carefully lift the rear camera connector up off its socket on the logic board.
-
Remove the rear camera.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the small circular white sticker (warranty sticker and water indicator) covering the screw near the battery pull tab.
-
Remove the 2.4 mm Phillips screw that was hidden underneath the sticker.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the edge of a plastic opening tool to gently pry the following connectors up and out of their sockets on the logic board:
-
Digitizer cable (pry from bottom)
-
LCD cable (pry from bottom)
-
Headphone jack/volume button cable (pry from top)
-
Top Microphone/sleep button cable (pry from top)
-
Front camera cable (pry from top)
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
Ferramenta utilizada nesse passo:Standoff Screwdriver for iPhones$5.49-
Remove the 4.8 mm standoff screw near the headphone jack.
-
Without this part, the motherboard could damage the ribbon cables around it.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully remove the logic board from the iPhone, minding any cables that may get caught.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the edge of a plastic opening tool to lift the thin steel front camera retainer off the front camera.
-
Remove the front camera retainer.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully lift the front facing camera out of the iPhone.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following two screws securing the vibrator to the inner frame:
-
One 6 mm Phillips screw
-
One 1.4 mm Phillips screw
-
Remove the vibrator from the inner case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the edge of a plastic opening tool to peel the small strip of black tape off the back of the volume button bracket.
-
Carefully remove the remaining portion of tape off the small section of ribbon cable near the inside of the bottom volume button.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the five Phillips screws securing the silent and volume button brackets to the outer case.
-
The screw directly below the silent switch is shorter than the others.
-
The left screw securing the volume control bracket is longer then the rest.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a pair of tweezers to carefully pull the silent switch and its bracket from the side of the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Grab the headphone jack with a pair of tweezers and remove the assembly from the iPhone, being careful not to rip the thin ribbon cables.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the edge of a plastic opening tool to peel the electronic portion of the silent switch off its metal bracket.
-
Transfer the bracket to the new silent switch.
-
Repeat this procedure to peel the metal volume button bracket off the electronic portion of the volume buttons.
-
Transfer the volume button bracket to the new volume buttons.
-
Cancelar: não concluí este guia.
264 outras pessoas executaram este guia.
Documentos anexados
13 comentários
In my opinion, the hardest part of this repair is bending and routing the flex cable, specifically around the headphone jack and cable connector. There is no picture or clear directions on how to do this anywhere that I can find. If done incorrectly, the flex will tear rendering your whole job a failure.
The part most difficult is to place all pieces without break the flat and after that turn the tinies screws. Now I'm happy with my iPhone working like new! Thank you iFixit ;)