Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully grasp the home button with a pair of tweezers.
-
Gently lower and place the home button into the round opening located at the bottom of the front panel.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully peel off the first trapezoidal adhesive strip.
I ordered the IPAD 2 BATTERY KIT (IF110-014-3 ). does this come with this adhesive strips?
Yes the iPad 2 battery kit includes everything you need, including the adhesive. The strips may look slightly different than the ones shown in this guide, but they will work the same. If you are only replacing the battery, you won’t need to remove or replace the home button, so ignore the home button bracket steps of this guide.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Using a pair of tweezers, place the first trapezoidal adhesive strip (minding its correct orientation) on the matching side of the home button mounting bracket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a pair of tweezers to grasp the corner of one of the adhesive strips placed on the mounting bracket.
-
Lift and peel the brown backing up off the adhesive strip, revealing the clear adhesive strip.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Gently place the home button mounting bracket on top of the home button.
-
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the largest L-shaped adhesive strip on the top left corner of the front panel.
-
Smooth the strip down from the center out, taking care to not trap any air bubbles between the strip and the front panel.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the thinnest L-shaped adhesive strip on the bottom left corner of the front panel.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the remaining thin L-shaped adhesive strip on the top right corner of the front panel, near the camera mounting bracket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the straight adhesive strip on the right side of the front panel.
-
If you've already attached the digitizer cable, you'll have to work around/under it to attach this strip.
I had already reattached the digitizer cable so I used an Exacto knife to trim the adhesive around the cable…worked like a charm.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the last L-shaped adhesive strip on the bottom right corner of the front panel.
hi, i had my front panel connecting strip torn during repair… what can i do??
i had my ipad 2 front panel connecting strip torn down during repair…
plz tell me the solution
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lay the thin T-shaped adhesive strip between the bottom edge of the inner frame of the front panel and the camera mounting bracket. The longest edge should be flush with the inner frame.
I believe this should go above the bracket. There is no metal to adhere to between the LCD and the camera.
No. Everything is showed correctly. This strip doesn't have to glue to metal, there are plastic spacers for it at the top of the LCD.
If you afraid the glass will be loose of the bezel then you can cut two thin stripes of another two sided tape and attach them to the bezel's plastic as an extra option.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Place the small hook-shaped adhesive strip below the left side of the home button mounting bracket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lay the final small rectangular adhesive strip to the left of the hook-shaped adhesive strip, immediately to the right of the thin L-shaped strip, and flush with the bottom of the front panel.
-
Cancelar: não concluí este guia.
128 outras pessoas executaram este guia.
2 comentários
I think a straight on picture showing all the adhesive pieces in place would be really helpful.
How am i supposed to put the digitizer cable back, and how do i put the fron on it?