Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
-
Ferramenta utilizada nesse passo:iMac Intel 27" Cardboard Service Wedge$4.99
-
Com a dobradiça podendo se mover livremente, o iMac fica instável, o que torna o trabalho difícil. Os reparos podem ser executados com o iMac deitado, mas ficam mais rápidos e fáceis se você usar um suporte de reparos para iMac.
-
Se estiver usando o suporte de reparo de papelão da iFixit, siga estas instruções de montagemestas instruções de montagem para instalá-lo.
-
-
Ferramenta utilizada nesse passo:Plastic Cards$2.99
-
Coloque o iMac numa mesa com a tela virada para cima.
-
Começando pelo canto direito superior do iMac, introduza um cartão de plástico por entre a tela e a moldura.
-
-
-
Com os cartões introduzidos próximo aos cantos, como mostra a figura, vire gentilmente os cartões para aumentar o vão entre a tela e a estrutura.
-
Se em algumas partes o adesivo ainda estiver colando e não puder ser separado, pare de fazer movimentos de vai-e-vem e use um dos cartões para cortar o adesivo nesta área.
-
Comece erguendo a parte superior da tela para fora da moldura.
-
-
-
-
Se houver um fio ou cabo debaixo da fita adesiva, remova sempre primeiro a fita.
-
Se o cabo estiver colado no chassi, use uma bolsa térmica iOpener ou um secador de cabelos para amolecer primeiro o adesivo. Você pode em seguida passar uma palheta de abertura por debaixo do cabo para soltá-lo. Nunca puxe diretamente pelos sensíveis conectores.
-
Passe uma palheta de abertura por debaixo dos pedaços de espuma para separá-los da tela e remova-os gentilmente. Pode ser que você precise de uma fita dupla-face para fixá-los na tela nova.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a Phillips screwdriver to remove the nine 3.2 mm screws securing the support bracket.
-
You may need to peel up the display adhesive lining the bottom edge of the iMac enclosure to access the screws.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the lower support bracket (a.k.a. "chin strap") from the iMac enclosure.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Unplug the left speaker cable by pulling it straight up out of its socket on the logic board.
-
De-route the cable from the gap between the hard drive and logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a spudger to disconnect the power button connector from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift the left speaker straight up, until the power button cable is exposed (about 0.5 inches).
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Gently de-route the power button cable from its groove in the left speaker.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift the left speaker straight up and remove it from the iMac.
-
Push from the connector end as you pull from the speaker end to thread the cable under the hard drive's right bracket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull straight up on the SATA data/power cable to disconnect it from the drive.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove two 7.3 mm T10 screws securing the left hard drive bracket to the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Grab the hard drive and left hard drive bracket together.
-
Tilt the left side up away from the rear case, and slide the assembly to the left.
-
Remove the hard drive and left hard drive bracket from the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the power supply control cable from the power supply.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following four screws securing the power supply to the rear case (size T8 or T10 depending on the exact model):
-
Two 23.7 mm Torx screws
-
Two 7.3 mm Torx screws
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Move the power supply board towards the left edge of the case and up to free it from the notch in the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Depress the tab on the DC power cable connector, then pull it straight out of its socket on the back of the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Flip the top of the power supply towards you, like opening a mailbox, to reveal the AC inlet cable connector.
-
Disconnect the AC inlet cable connector.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Gently rock the right speaker slightly to the right, to allow access to its cable's connection on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use a spudger to loosen the right speaker cable's connector from its socket on the logic board.
-
Pull the connector to the right to remove it from its socket.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift the speaker straight up and remove it from the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the tip of a spudger to disconnect the fan cable's connector from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Peel the black tape connecting the fan to the exhaust duct back slightly.
-
Leave the tape in place on the exhaust duct—you only need to expose the joint to free the fan.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove three 12.4 mm T10 screws securing the fan to the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the flat end of a spudger to disconnect each of the four antenna connectors from the AirPort/Bluetooth card.
-
Leftmost
-
Top
-
Upper right
-
Lower right
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Flip up the metal retaining bracket on the iSight camera cable.
-
Pull the camera cable connector straight out of its socket, toward the top of the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the flat end of a spudger to disconnect the headphone jack cable connector from its socket on the logic board.
-
Gently push the cable out of the way.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following screws from the front of the logic board:
-
Two 23.7 mm T10 screws
-
Four 7.4 mm T10 screws
-
One 20.8 mm T25 spacer screw
-
One captive T10 screw
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the cable and connector through the right hard drive bracket. Move the cable to the right side of the iMac, out of the way of the exhaust port.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove two 5.7 mm T10 screws from the top of the heat sink exhaust duct.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Tilt the logic board slightly forward.
-
Lift the logic board straight up and out of the iMac. Be careful not to snag on any of the screw posts attached to the inside of the rear case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
When reassembling your iMac, be very careful to align the exterior I/O ports correctly. The logic board can sit crooked even when secured with all its screws.
-
You can use a USB flashdrive or ethernet cable to ensure the logic board is seated correctly while you screw it in.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull up on the SATA power cable connector to disconnect it.
-
Unplug the SATA data cable connector by depressing its locking tab and pulling straight up on the connector.
-
Remove the SATA cable from the logic board assembly to get it out of the way and prevent it from being damaged.
-
Cancelar: não concluí este guia.
15 outras pessoas executaram este guia.
6 comentários
Where can I get this S-ATA cable. I bought an Apple iMac 27 inch with 5K display in a BTO configuration with 1 TB internal SSD (flash) and NO internal HDD (classic drive) and would like to put a big (like 6 TB) disk in it. After opening the iMac I realized that the S-ATA cable (mentioned above) is missing. Any hint to a source is appreciated.
Hi, are you sure that is the same cable? i have the same question, because there is says its a replacement hard drive power and data cable for the late 2014 through Mid 2015 iMac 27"
andres -