Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.
O que você precisa
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Loosen the three Phillips screws securing the access door to the bottom edge of your iMac.
-
Remove the access door from your iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
Ferramenta utilizada nesse passo:Heavy-Duty Suction Cups (Pair)$14.95-
Stick a suction cup near each of the two top corners of the glass panel.
-
If your suction cups refuse to stick, try cleaning both the glass panel and the suction cup with a mild solvent.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Gently lift the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the top edge of the glass panel.
-
Pull the glass panel away from the lower edge of the iMac and carefully set it aside.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the eight 8 mm T10 Torx screws securing the display to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Slightly lift the top edge of the display out of the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the vertical sync ribbon cable out of its socket on the LED driver board near the top left corner of your iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Squeeze the two display data cable connector arms together to unlock it from its socket on the logic board.
-
Pull the display data cable connector away from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the LCD thermal sensor cable connector from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following four screws securing the power supply to the outer case:
-
Two 22.2 mm fine-thread T10 Torx
-
One 25 mm coarse-thread T10 Torx
-
One 9 mm coarse-thread T10 Torx
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully lift the power supply out of the outer case and rotate it to expose the cable lock as shown, minding the DC-Out cable still attaching it to the iMac.
-
Disconnect the DC-In cable by depressing the locking mechanism on the connector while you pull the connector away from its socket on the power supply.
-
Once the locking mechanism has cleared the socket, pull the DC-In connector away from the power supply.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the AC-In cable by depressing the locking mechanism while pulling the connector away from its socket.
-
Remove the power supply from the outer case.
-
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the optical drive thermal sensor connector straight away from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the four 9 mm T10 Torx screws securing the optical drive to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Lift the inner edge of the optical drive and maneuver its connector past the frame attached to the logic board.
-
Carefully pull the optical drive off its mounting pins on the edge of the outer case to gain clearance for disconnecting the optical drive cable.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use the flat end of a spudger to help disconnect the optical drive cable.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the single 13 mm T10 Torx screw securing the optical drive fan to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the optical drive off the pins attached to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the optical drive fan connector away from its socket on the logic board.
-
Remove the optical drive fan from the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Pull the left and right speaker connectors toward the right side of the iMac to disconnect them from the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the audio port cable by pulling its connector toward the right side of the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the AirPort cable by lifting its connector off the socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the following cables by pulling their connectors toward the top edge of the iMac:
-
Camera cable
-
Hard drive thermal sensor
-
Hard drive fan
-
Microphone
-
Disconnect the following cables by pulling their connectors toward the right edge of the iMac:
-
Ambient temperature sensor
-
Bluetooth cable
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the CPU fan and power button by pulling their connectors toward the left edge of the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
If present, remove the piece of tape covering the IR sensor connector.
-
Disconnect the IR sensor by pulling its connector toward the top edge of the iMac.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Use your fingers to lift IR sensor assembly straight up out of the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the following six screws securing the logic board to the outer case:
-
Three 25 mm T10 Torx
-
Two 21.5 mm T10 Torx
-
One 7 mm T10 Torx
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the plastic ducts from the side of the LED driver board and the hard drive by pulling them away from the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully remove the aluminum tape attaching the GPU heat sink to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully pull the logic board slightly away from the outer case.
-
While holding the board away from the outer case, rotate the board back and forth while lifting up to release it from the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Now that the lower edge of the board is free from the outer case, rotate the logic board toward yourself to expose its rear face.
-
Carefully pull the optical drive connector away from its socket on the logic board.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Disconnect the DC-In cable from the logic board by simultaneously depressing the locking lever on the connector while pulling it away from its socket.
-
Remove the logic board from the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Carefully de-route the right speaker cable connector through the channel in the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove two T10 Torx screws securing the audio ports to the outer case.
-
Lift the audio ports out of the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Remove the single 13 mm T10 Torx screw securing the right speaker assembly to the outer case.
-
-
Este passo não foi traduzido. Ajude a traduzi-lo
-
Gently lift the right speaker assembly out of the outer case.
-
Cancelar: não concluí este guia.
2 outras pessoas executaram este guia.