Skip to main content

Changes to Making a low cost light stand for Photography Introduction

Edição por Nick

Edição aprovada by Nick

Excluído
Adicionado
Sem alteração
Introduction
a (broken) broken standing lamp by removing the lamp components. This lamp is While I am using a common style and should cover 99% of them but Mainstays lamp for this guide, there may be minor variations. This will variations in lamps from different stores/brands. These are usually minor. It does not impact the guide, but this is something to keep in mind. may change how certain components are removed. This guide will also help you identify reusable components for other projects. [ … ] get as modifications and may be required, require modificiation, these lamps are cheap or even usually free because they are so common and inexpensive.''''' or inexpensive for used ones.''''' This can be advantageous if you are willing to disassemble one to eliminate the redundant components. == Guide notes == * '''''Use common sense during the cord and socket removal procedure. Death or injury may occur if you make a mistake, as you are handing 120-240V AC!''''' or is missing parts that cannot be readily purchased. Post disassembly reversal use a damaged one. Reversal may be impractical, especially impractical if you used a broken lamp that needed other parts and made modifications. modifications are made. * If possible, use a lamp with a dangerous problem like a busted socket guard cover, as the one in this guide had a problem with. The one I used in this guide This part was cracked and was supported with electrical tape until it was pulled out of service due to redundancy. service. These are the best candidate for this type of project, as they cannot these parts can be used difficult to find without major repairs and a donor or the parts cost often exceeds exceed the entire cost of a new lamp. * While the plastic parts on many of these lamps may not (easily) be reusable (either due to assembly technique or uniqueness) in every situation, the cord and socket can be easily reused. Save these for another project if they are in good condition. * '''''DO NOT keep any part that looks damaged. Consider Discard these parts garbage for good measure.''''' safety reasons.'''''
a (broken) broken standing lamp by removing the lamp components. This lamp is While I am using a common style and should cover 99% of them but Mainstays lamp for this guide, there may be minor variations. This will variations in lamps from different stores/brands. These are usually minor. It does not impact the guide, but this is something to keep in mind. may change how certain components are removed. This guide will also help you identify reusable components for other projects. [ … ] get as modifications and may be required, require modificiation, these lamps are cheap or even usually free because they are so common and inexpensive.''''' or inexpensive for used ones.''''' This can be advantageous if you are willing to disassemble one to eliminate the redundant components. == Guide notes == * '''''Use common sense during the cord and socket removal procedure. Death or injury may occur if you make a mistake, as you are handing 120-240V AC!''''' or is missing parts that cannot be readily purchased. Post disassembly reversal use a damaged one. Reversal may be impractical, especially impractical if you used a broken lamp that needed other parts and made modifications. modifications are made. * If possible, use a lamp with a dangerous problem like a busted socket guard cover, as the one in this guide had a problem with. The one I used in this guide This part was cracked and was supported with electrical tape until it was pulled out of service due to redundancy. service. These are the best candidate for this type of project, as they cannot these parts can be used difficult to find without major repairs and a donor or the parts cost often exceeds exceed the entire cost of a new lamp. * While the plastic parts on many of these lamps may not (easily) be reusable (either due to assembly technique or uniqueness) in every situation, the cord and socket can be easily reused. Save these for another project if they are in good condition. * '''''DO NOT keep any part that looks damaged. Consider Discard these parts garbage for good measure.''''' safety reasons.'''''
Summary
to use reuse an old standing lamp that needs expensive work to create one.
to use reuse an old standing lamp that needs expensive work to create one.

Ferramentas

  • 64 Bit Driver Kit Phillips #2 bit x1 Substitutable with a drill and Phillips #2 bit or standalone driver. (featured) added.
  • Flush Wire Cutters x1 Used on push sockets. Cut the cord a distance away from the socket for reuse. added.
  • 64 Bit Driver Kit x1 Use Phillips #2 bit. Substitutable with a drill and Phillips #2 bit. (featured) removed.
  • Flush Wire Cutters x1 Used on push sockets. Cut the cord a distance away from the socket to reuse these. removed.