Conserte seus objetos Comunidade Loja

Zenithink ZTPAD ZT280 C91 Front Panel Replacement

Introdução

Be sure to follow the prerequisite guides before removing the front panel. Skipping any of the guides can lead to damage to your device.

O que você precisa

  1. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Back Panel: passo 1, imagem 1 %32

    • Remove the two screws on the bottom using a Phillips #00 screwdriver.

    • For differentiation purposes, these screws are 4mm long.

    Editar

  2. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 2, imagem 1 %32 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 2, imagem 2 %32 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 2, imagem 3 %32

    • Using a spudger, start prying the case apart by working around the edge slowly.

    • Be careful not to damage any of the latches that hold the back panel in place, especially if you are using a metal spudger.

    • While prying, be careful to not lose the power and volume buttons; the case is the only thing holding them in place so they will easily come out once the panel has been removed

    • Be careful to not damage the speaker cables, they will still be connecting both panels.

    Editar

  3. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Motherboard: passo 3, imagem 1 %32

    • Peel back the touch interface chip (which is on the top right of the motherboard, covered in yellow tape.)

    Editar

  4. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 4, imagem 1 %32

    • Flip up the small gate and unplug the ribbon cable shown.

    Editar

  6. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 5, imagem 1 %32

    • Using a Phillips #00 screwdriver, remove the screws highlighted with the orange rings as shown in the picture.

    • For differentiation purposes, these screws are 3.5mm long.

    Editar

  7. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 6, imagem 1 %32
    Ferramenta utilizada nesse passo:
    Tweezers
    $4.99
    Comprar

    • Slide back the plastic latch for the main display cable.

    • Carefully unplug the cable with tweezers.

    Editar

  8. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 7, imagem 1 %32 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 7, imagem 2 %32

    • Slide back the plastic latch for the camera cable.

    • Carefully unplug the cable with tweezers.

    Editar

  9. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 8, imagem 1 %32

    • Peel back the reflective tape.

    Editar

  10. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 9, imagem 1 %32 Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 9, imagem 2 %32

    • Lift up the motherboard assembly, starting by lifting up the top.

    • Be careful not to damage any of the ports on the underside of the tablet.

    • The camera cable will slide through a small notch and end up underneath the board.

    Editar

  11. Zenithink ZTPAD ZT280 C91 Front Panel Replacement, Front Panel: passo 10, imagem 1 %32

    • Remove the four highlighted screws using a Phillips #1 screwdriver.

    • For differentiation purposes, these screws are 4mm long and have a larger head than the rest of the screws.

    Editar

  12. Zenithink ZTPAD ZT280 C91 Front Panel Replacement: passo 11, imagem 1 %32

    • Starting from the top, slowly lift everything up out of the front panel.

    • Remove the front panel off of the device.

    • Be careful not to damage the ports along the bottom.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 4

Duração total: 144