Ir para o conteúdo principal

VTech InnoTab 2s Power Connector Replacement

O que você precisa

  1. VTech InnoTab 2s Power Connector Replacement, Back Panel: passo 1, imagem 1 %32
    • Turn your device to where the back panel is facing you.

  2. VTech InnoTab 2s Power Connector Replacement: passo 2, imagem 1 %32 VTech InnoTab 2s Power Connector Replacement: passo 2, imagem 2 %32
    • Lift the Leg all the way up and twist the bottom to remove.

    • Once the bottom part pops out the whole leg should just come off.

    • Remove any game cartridge from the device.

  3. VTech InnoTab 2s Power Connector Replacement: passo 3, imagem 1 %32 VTech InnoTab 2s Power Connector Replacement: passo 3, imagem 2 %32 VTech InnoTab 2s Power Connector Replacement: passo 3, imagem 3 %32
    • Remove all of the plastic tabs on the device. These are covering screws that will need to be removed.

    • These covers are made of hard plastic so they may be difficult to remove.

    • There is a special tab in the cartridge cover that is made of rubber, make sure to not break this tab.

  4. VTech InnoTab 2s Power Connector Replacement: passo 4, imagem 1 %32 VTech InnoTab 2s Power Connector Replacement: passo 4, imagem 2 %32
    • Remove all nine screws from the back of the device using a J0 bit.

    • Remove the small battery.

  5. VTech InnoTab 2s Power Connector Replacement: passo 5, imagem 1 %32 VTech InnoTab 2s Power Connector Replacement: passo 5, imagem 2 %32
    • Using a plastic opening tool, detach the backplate from the front piece.

    • Do not use excessive force. Double check that you removed all the screws if the panel is not coming off easily.

    • Once the backplate has been removed, you will have access to the circuit board.

  6. VTech InnoTab 2s Power Connector Replacement, Motherboard: passo 6, imagem 1 %32
    • First begin by removing the three cross-head screws using a J0 bit.

  7. VTech InnoTab 2s Power Connector Replacement: passo 7, imagem 1 %32
    • First remove the ribbon cables. There are two highlighted by the red squares

    • Do not apply too much pressure and make sure that the black plastic tabs are fully open before you pull the cable out.

  8. VTech InnoTab 2s Power Connector Replacement: passo 8, imagem 1 %32
    • Remove the camera from the assembly and put is a safe place so that it will not get damaged.

  9. VTech InnoTab 2s Power Connector Replacement: passo 9, imagem 1 %32
    • Remove the board from the main assembly.

    • Be careful not to pull too hard so that the cables aren't broken.

  10. VTech InnoTab 2s Power Connector Replacement: passo 10, imagem 1 %32
    • De-solder the points shown to fully remove the cables and free the board.

    • A soldering guide offered by IFIXIT can be found here Soldering Skills.

  11. VTech InnoTab 2s Power Connector Replacement, Power Connector: passo 11, imagem 1 %32
    • Use a soldering tool to desolder the two highlighted points.

    • A soldering guide offered by IFIXIT can be found here: Soldering Skills.

  12. VTech InnoTab 2s Power Connector Replacement: passo 12, imagem 1 %32
    • Use a screwdriver to remove the screw that is holding the power jack in place.

    • Now you have access to remove and replace the power jack.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Esthevan Romeiro

Membro desde: 10/06/16

261 Reputação

Autoria de 4 guias

Equipe

USF Tampa, Team 5-1, Lacy Fall 2016 Membro de USF Tampa, Team 5-1, Lacy Fall 2016

USFT-LACY-F16S5G1

Membros da 4

Autoria de 12 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Duração total: 325