Conserte seus objetos Comunidade Loja

Toshiba Satellite A105-S4284 Casing Replacement

Escrito Por: Josh (e 2 outros contribuidores)
  • Comentários: 0
  • Favoritos: 0
  • Execuções: 1

Dificuldade

Moderado

Passos

7

Tempo necessário

15 - 20 minutos

Partes

2

Sinalizadores

1

Better Introduction

Melhor Introdução

Melhore este guia, completando ou revendo a sua introdução.

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

  1. Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.

    • Flip the laptop over so it is rightside up, and open the laptop all the way so that the screen is horizontal.

    Editar

  2. Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker. Use the plastic opening tool to pop off tabs along the length of this panel. This may feel like you're about to break something, but as long as you work your way down the panel and don't yank it out, the laptop will be fine.

    • Using the plastic opening tool, pry off the panel above the keyboard, starting near the right front speaker.

    • Use the plastic opening tool to pop off tabs along the length of this panel.

    • This may feel like you're about to break something, but as long as you work your way down the panel and don't yank it out, the laptop will be fine.

    Editar

  3. Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver. Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.

    • Unscrew the two 4.5 mm screws holding the keyboard on with the Phillips #1 screwdriver.

    Editar

  5. Lift the keyboard gently from the side closest the screen. Pull out the ribbon connecting the keyboard to the laptop. Pull out the ribbon connecting the keyboard to the laptop.

    • Lift the keyboard gently from the side closest the screen.

    • Pull out the ribbon connecting the keyboard to the laptop.

    Editar

  6. Disconnect wire attaching LCD to motherboard Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.

    • Disconnect wire attaching LCD to motherboard

    • Using the Phillips screwdriver remove the two 4.0mm screws from each hinge above speakers

    • Partially close the lid and remove the last two 4.0mm screws from the back of the laptop.

    Editar

  7. Remove the seventeen 4.5mm phillips screws on the bottom of the laptop. Using the pry tool separate the two halves of the laptop base.

    • Remove the seventeen 4.5mm phillips screws on the bottom of the laptop.

    • Using the pry tool separate the two halves of the laptop base.

    • Use caution when separating the laptop halves as they are still connected by two ribbon cables.

    Editar

  8. Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard. Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.

    • Lift the top half of the case enough to get your hand beneath it, and then remove the two ribbon cables that connect it to the motherboard.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor(a)

com 2 outros contribuidores

Josh

Membro desde: 12/03/2014

625 Reputação

5 Guias de autoria

Emblemas: 8

+5 outros emblemas

Equipe

UMass Dartmouth, Team 1-6, Cichon Spring 2014 Membro de UMass Dartmouth, Team 1-6, Cichon Spring 2014

UMASSD-CICHON-S14S1G6

3 Membros

6 Guias de autoria

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Duração total: 768