Ir para o conteúdo principal

Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.

O que você precisa

  1. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 1, imagem 1 %32 : passo 1, imagem 2 %32
    • Using tweezers, gently remove the two stabilizing links by pulling straight away from the point of connection.

  2. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 2, imagem 1 %32 : passo 2, imagem 2 %32
    • Remove the counterweight bar by removing the screw.

    • One 10.1mm Phillips #0.

  3. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 3, imagem 1 %32 : passo 3, imagem 2 %32
    • Remove the gyro carriage by removing the following screws:

    • Two 5.6mm Phillips #0.

    • When reinstalling these screws make sure to line up one screw with the keyway on the main rotor shaft.

  4. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 4, imagem 1 %32 : passo 4, imagem 2 %32
    • Gently remove the broken gyro carriage by pulling up.

    • Remove blade assembly by simply sliding it up and off the shaft.

  5. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 5, imagem 1 %32 : passo 5, imagem 2 %32 : passo 5, imagem 3 %32
    • Again using tweezers gently remove the stabilizing links from the blade carriage by pulling straight away from the point of connection.

  6. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 6, imagem 1 %32 : passo 6, imagem 2 %32
    • Remove the blades from the blade carriage by removing the following screws:

    • Two 4.7mm Phillips #0.

  7. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 7, imagem 1 %32 : passo 7, imagem 2 %32
    • Remove the following screws:

    • Two 4.5mm Phillips #0.

    • Make sure to remove any broken plastic pins before reassembling the components.

    • You will have to slide the two halves of the blade carriage over the pins on the gyro carriage first when reassembling.

Linha de Chegada

7 outras pessoas executaram este guia.

Christopher Smith

Membro desde: 10/11/14

305 Reputação

Autoria de 1 guia

Equipe

USF Tampa, Team 1-31, Donnelly Fall 2014 Membro de USF Tampa, Team 1-31, Donnelly Fall 2014

USFT-DONNELLY-F14S1G31

1 Membro

1 Guia de autoria

6 comentários

Thank you for this guide! This has fixed the issue and made a 35 year old boy very happy!

Patrick haymer - Responder

Cheers thanks too this page I fixed problem  great ,  Martin

Martin Worboys - Responder

Same here, incidentally where can I get replacement batteries please? Also have a “Picolo” heli with a bad feedback IC , supposedly this part can also be replaced on some units as its a soldered vertical board on the main.

Andre - Responder

Thank you! Took forever to find an answer to my problem! Now very obvious thanks to you. My sanity is restored! HaHa!

CRC 04/04/2021

Chris - Responder

I’m halfway there and grateful for the directions. But I’m not having any luck removing the broken plastic pins from the blade carriage. I’ve tried using a needle but no luck. Did anyone else come up against this?

Adam Leavesley - Responder

Now it flies in an oval pattern wat am I doing wrong?

prober1212 - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 7

Últimos 30 dias: 21

Duração total: 14,180