Introdução

This guide covers the Sony Xperia XZ Premium headphone jack removal.

Place a heated iOpener on the back panel of the phone to melt the adhesive inside.
  • Place a heated iOpener on the back panel of the phone to melt the adhesive inside.

  • The iOpener or your desired heat source can be very hot and can heat up the phone, so make sure you do not burn yourself.

  • Follow this guide for directions on using the iOpener.

Adicionar comentário

Slide a thin plastic card under the back panel and around the perimeter of the phone to remove the adhesive.
  • Slide a thin plastic card under the back panel and around the perimeter of the phone to remove the adhesive.

Adicionar comentário

  • Take hold of the back panel with your fingers and remove.

Adicionar comentário

  • Orient the phone horizontally with the front screen facing down and the camera on the bottom left corner.

Adicionar comentário

  • Remove nine 3.9mm Phillips #000 screws.

  • Make sure to turn carefully in the counter-clockwise direction or you may wear out the thread and shape of the screws. You will not be able to remove the screws once they are damaged!

  • When unscrewing, remember "Left Loosey, Righty Tighty!"

Adicionar comentário

  • Place the spudger under the top left corner frame piece and lift to loosen.

Adicionar comentário

  • Grab hold of the top left frame piece with your fingers and gently wiggle and lift to remove.

Adicionar comentário

  • Place the spudger under the bottom left frame piece and lift to loosen it.

Adicionar comentário

  • Grab hold of bottom left frame piece with your fingers and lift gently.

  • When dislodging the left frame piece, carefully wiggle the piece while lifting it vertically to prevent any damage to the wedges on the frame. This applies for all of the other frame pieces you will remove after this step!

Adicionar comentário

  • Place the spudger under the top right frame piece and lift to loosen it.

Adicionar comentário

  • Grab hold of the top right frame piece with your fingers and lift.

Adicionar comentário

  • Insert your nail under the top left connector and push to disconnect it.

Adicionar comentário

  • Grab hold of the metal part of the connector with your fingers and lift.

Adicionar comentário

  • Insert your nail under the metal part of the bottom left connector.

Adicionar comentário

  • Push the bottom left connector with your finger to disconnect it.

Adicionar comentário

  • Insert your nail under the center topmost connector and push to loosen it.

Adicionar comentário

  • Grab hold of the top connector with your fingers and lift to disconnect it.

Adicionar comentário

  • Insert your nail under the metal tab of the connector above the battery and push to loosen it.

Adicionar comentário

  • Pull the metal tab of the connector towards you with your fingers to disconnect the pins.

Adicionar comentário

  • Insert spudger in the gap above the battery and lift to loosen the motherboard.

  • Use the spudger to slide under the edges of the motherboard if the motherboard does not seem to loosen after the above step.

Adicionar comentário

  • Insert the spudger in the gap between the motherboard and the left side of the battery to further lift out the motherboard.

Adicionar comentário

  • Grab hold of the motherboard with your fingers and lift it out of the phone gently.

Adicionar comentário

  • Insert the spudger in the gap to the bottom of the headphone jack.

Adicionar comentário

  • Gently extract the headphone jack by pulling the orange tab with your fingers.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Bolaji Makinde

Member since: 18-04-2018

85 reputação

Autoria de 1 guia

Equipe

Cal Poly, Team S18-G2, Livingston Spring 2018 Membro de Cal Poly, Team S18-G2, Livingston Spring 2018

CPSU-LIVINGSTON-S18S18G2

5 Membros

6 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 4

Últimos 30 dias: 17

Todo: 117