Introdução

You will need to use a source of heat. You may need to buy adhesive for the reassembly. Make sure the phone is completely powered off before opening the device.

Apply heat  on the back surface of the phone.
  • Apply heat on the back surface of the phone.

  • Continue to heat the device as needed throughout the replacement process.

  • The device can get very hot, so be careful when handling it.

Adicionar comentário

Stick the small suction cup on the bottom half of the back surface of the phone.
  • Stick the small suction cup on the bottom half of the back surface of the phone.

Adicionar comentário

With the bottom of the device facing you, lift up on the suction cup handle. Use the plastic opening tool around all sides to pry off the back cover. Use the plastic opening tool around all sides to pry off the back cover.
  • With the bottom of the device facing you, lift up on the suction cup handle.

  • Use the plastic opening tool around all sides to pry off the back cover.

Adicionar comentário

Pull the back of the phone case away from the device. You will hear popping sounds of glue being ripped from the phone. You will hear the sound of the back unlatching from the device.
  • Pull the back of the phone case away from the device.

  • You will hear popping sounds of glue being ripped from the phone.

  • You will hear the sound of the back unlatching from the device.

  • You will need to apply adhesive or glue along the device to have maximum seal in reassembly.

  • RAF antenna may be attached to the back cover upon removal.

Adicionar comentário

Apply heat to the copper RAF antenna.
  • Apply heat to the copper RAF antenna.

  • This step and the following step only apply if the RAF antenna does not come off when taking the back cover off.

Adicionar comentário

Peel back the RAF antenna.
  • Peel back the RAF antenna.

Adicionar comentário

Remove the five black 4mm screws with a Phillips #00 screwdriver. Remove the five black 4mm screws with a Phillips #00 screwdriver.
  • Remove the five black 4mm screws with a Phillips #00 screwdriver.

Adicionar comentário

Pry up the black camera case with the plastic opening tool and then remove the case. Pry up the black camera case with the plastic opening tool and then remove the case. Pry up the black camera case with the plastic opening tool and then remove the case.
  • Pry up the black camera case with the plastic opening tool and then remove the case.

Adicionar comentário

Use the flat end of the spudger to peel up the copper tab to the right of the back camera. Peel back the tab past the connector.
  • Use the flat end of the spudger to peel up the copper tab to the right of the back camera.

  • Peel back the tab past the connector.

  • Tab is stuck with adhesive.

Adicionar comentário

Pry up the camera's connector to the motherboard with the nylon spudger.
  • Pry up the camera's connector to the motherboard with the nylon spudger.

Adicionar comentário

Use the flat end of the nylon spudger to lift the camera out of the phone.
  • Use the flat end of the nylon spudger to lift the camera out of the phone.

Adicionar comentário

Finish removing the front camera by lifting it gently with your fingers.
  • Finish removing the front camera by lifting it gently with your fingers.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Theresa Wilcoski

Member since: 18-04-2018

270 reputação

2 Guides authored

Equipe

Cal Poly, Team S17-G2, Livingston Spring 2018 Membro de Cal Poly, Team S17-G2, Livingston Spring 2018

CPSU-LIVINGSTON-S18S17G2

4 Membros

8 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 9

Todo: 40