Introdução

How to remove the upper casing of the Sony Vaio VGN-S260 laptop

Peças

Não são necessárias peças.

  1. Flip the laptop over so the Vaio logo is facing down
    • Flip the laptop over so the Vaio logo is facing down

    • Locate the battery at the top and Find the release and unlock slides on the battery

    • Slide the unlock tab to the unlock position

    • Slide the release tab in the direction of the arrow, i.e. towards the unlock tab

    Adicionar comentário

  2. With the tabs still in the unlock position, slide the battery away from the main case.
    • With the tabs still in the unlock position, slide the battery away from the main case.

    Adicionar comentário

    • Flip the computer over so the Vaio logo is facedown

    • Unscrew the 2 screws next to the battery

    Adicionar comentário

    • Flip the computer over again so the Vaio logo is face up

    • Open the lid

    Adicionar comentário

    • Press down on the outer gray shell around the keyboard

    • Use the spudger to gently lift keyboard

    • Do not pull up the keyboard too far as it is attached to a ribbon underneath

    There are 2 spring-held latches, one above the F4 and one above the F12. Push a latch up into the frame of the keyboard, then lift the keyboard gently in that area so the latch doesn't spring back. Then push the other latch and the keyboard will be released.

    Yishai Sered - Responder

    • Lift up lever underneath the ribbon to detach the keyboard.

    Adicionar comentário

    • Remove memory/wireless compartment cover

    Adicionar comentário

    • Flip so the Vaio Logo is face down

    • Locate and remove a total of 8 screws on the bottom.

    There are 2 more screws on the bottom, one in the middle of the front next to the flash stick socket, and one under the memory door.

    Yishai Sered - Responder

    • Find and remove 5 screws (they all have arrows next to them) from cover

    Adicionar comentário

    • Flip the laptop over so the Vaio logo is face up

    • Use the spudger to pop up the upper casing

    • Do not lift too much as the Uppercasing is attached to wires underneath

    • Remove the wires that are attaching the uppercasing to the motherboard

    There are also 5 screws from the top of the uppercasing.

    Yishai Sered - Responder

    The are 4 cables to remove: flat cable for the power and S buttons at top center; flat cable for the touchpad at bottom center; and 2 twisted pairs for the speakers.

    The speaker cable socket is very delicate. If all you are getting at is the CPU or the hard drive, it may be enough to disconnect the flat cables and gently rotate the uppercasing shifting it left to allow access to the right-hand side with the CPU fan and the hard drive.

    Yishai Sered - Responder

    The top panel has cutouts that allow the cables to be disconnected before the top of the case is removed. The two flat cables are not clamped and can be pulled vertically out of their connectors. The delicate speaker cables are connected to the motherboard with plugs which can be gently levered up out of their sockets.

    roberttrevellyan - Responder

    • Remove the uppercasing

    Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

2 outras pessoas concluíram este guia.

Jeffrey Bryan

Member since: 20-04-2010

552 reputação

11 Guides authored

Equipe

Cal Poly, Team 16-4, Maness Spring 2010 Membro de Cal Poly, Team 16-4, Maness Spring 2010

CPSU-MANESS-S10S16G4

4 Membros

11 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 6

Todo: 4,425