Ir para o conteúdo principal

Sony Cyber-shot DSC-HX90V Motherboard Replacement

O que você precisa

  1. Sony Cyber-shot DSC-HX90V Motherboard Replacement, Button board: passo 1, imagem 1 %32
    • Place the device so bottom of the camera is facing up .

    • Remove the five black M1.4 X 3.5 Phillips head screws with a Phillips #000 screwdriver.

  2. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 2, imagem 1 %32
    • Remove the marked black M1.4 X 3.5 Phillips head screws on the side of the camera with a Phillips #000 screwdriver.

  3. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 3, imagem 1 %32
    • Remove the marked screw with a Phillips #000 screwdriver.

  4. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 4, imagem 1 %32 Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 4, imagem 2 %32
    • Use the plastic opening tool to remove the button board.

  5. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 5, imagem 1 %32 Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 5, imagem 2 %32
    • Disconnect the control board data cable with care. Permanent damage may occur to the control board if tools are used to disconnect the data cable. Use your fingers only.

    • Disconnect the control board data cable by wiggling carefully with your fingertips. Set the control board to the side once it is disconnected.

  6. Sony Cyber-shot DSC-HX90V Motherboard Replacement, Side cover: passo 6, imagem 1 %32
    • Use the plastic opening tool with a prying motion to remove the side cover of the camera.

    • The cover should come off easily but you might hear light snapping or popping.

  7. Sony Cyber-shot DSC-HX90V Motherboard Replacement, LCD: passo 7, imagem 1 %32
    • Orient the device so the lens is facing down.

    • Remove the two black M1.4 X 3.5 Phillips head screws using Phillips #000 screwdriver.

  8. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 8, imagem 1 %32
    • Orient the device so the lens is facing down.

    • Remove the black M1.4 X 3.5 Phillips head screw.

  9. Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 9, imagem 1 %32 Sony Cyber-shot DSC-HX90V Motherboard Replacement: passo 9, imagem 2 %32
    • LCD screen is very fragile. Handle with care. Do not use tools to remove the screen.

    • Remove the ribbon cable connecting LCD display to camera sensor and battery housing.

  10. Sony Cyber-shot DSC-HX90V Motherboard Replacement, Motherboard: passo 10, imagem 1 %32
    • Make sure all ribbon cables are unplugged and remove the motherboard.

    • Ribbon wires can be easily damaged.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Marin Rusinov

Membro desde: 02/02/17

853 Reputação

Autoria de 5 guias

2 comentários

super Anleitung, trotz aller Vorsicht ist ein Flachbandkabel kaputt gegangen, und zwar das 2 adrige zu Sucher. Wie kann man Flachbandkabel reparieren oder ersetzen?

LG

Michael

Michael Bühnen - Responder

Hello!

Nice help to open the camera for fixing viewfinder problems: when not switching on, even when FINDER/MONITOR mode on FINDER, there might be a bad contact in the visor connector. It is a snap lock micro connector, open the lock, then carefully remove clean and replace ribbon cable:this may clear the trouble.

But attention: At least on HX9O without V ext. there are some more screws ;-) and niceties

- one in step 3, under the MULTI connector cap

- 3 on different places to remove LCD screen

Also, there is also an antenna , connected to the LCD assembly and lightly glued on the side

Frantz Bernhard - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 4

Últimos 30 dias: 39

Duração total: 3,017