Conserte seus objetos Comunidade Loja

Shark Rotator Powered Lift-Away Speed Roller Brush Replacement

Introdução

The roller brush can have debris that will cause the vacuum to not work properly. It is important that you always clean your roller brush after every use, so that your Shark Rotator Powered Lift Away Speed Vacuum can perform at it's best. This guide will show you how to change your roller brush if it becomes damaged or is broken.

O que você precisa

  1. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement, Belt: passo 1, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement, Belt: passo 1, imagem 2 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement, Belt: passo 1, imagem 3 %32

    • Turn the vacuum on its side.

    • Using a quarter, twist the three green locks to the unlock position.

    • Pull the bottom roller brush cover to open the vacuum.

    Editar

  2. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 2, imagem 1 %32

    • Using a T20 screwdriver, remove the five 15.9 mm screws on the outside cover.

    Editar

  3. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 3, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 3, imagem 2 %32

    • Remove the three 14.3 mm screws with a T20 screwdriver.

    Editar

  4. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 4, imagem 1 %32

    • Remove the two 14.3 mm screws under the wheels with a T20 screwdriver bit.

    Editar

  5. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 5, imagem 1 %32

    • Remove the two 15.9 mm screws from behind the wheels with a T20 bit screwdriver.

    Editar

  6. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 6, imagem 1 %32

    • Remove the single 13.4 mm small screw behind the roller brush with a PH0 screwdriver bit.

    Editar

  8. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 7, imagem 1 %32

    • Remove the single 13.4 mm screw from behind the belted end of the roller brush with a T20 screwdriver bit.

    Editar

  9. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 8, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 8, imagem 2 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 8, imagem 3 %32

    • Turn the vacuum around.

    • Using a spudger, pry the top of the vacuum cover off. There are three tabs behind each of the clear rectangles below the headlights.

    Editar

  10. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 9, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 9, imagem 2 %32

    • Remove both of the headlight covers with the spudger.

    Editar

  11. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 10, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 10, imagem 2 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 10, imagem 3 %32

    • Remove the grey side panel on the motor side of the vaccum with a spudger. Pry under each tab to release the side panel.

    Editar

  12. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 11, imagem 1 %32

    • Remove the two 13.4 mm screws with a T20 bit screwdriver.

    Editar

  13. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 12, imagem 1 %32

    • Remove the single 13.4 mm screw located next to where the belt was detached, securing the motor in place, with a PH1 screwdriver.

    Editar

  14. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 13, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 13, imagem 2 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 13, imagem 3 %32

    • Remove the visible side of the belt from the gear with a spudger.

    Editar

  15. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 14, imagem 1 %32

    • Remove the grey panel from the opposite side, by uncrewing the single 13.4 mm screw with a PH1 screwdriver. This will release the container for the roller brush and belt motor.

    Editar

  16. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 15, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 15, imagem 2 %32

    • Using the spudger, push the white end cap out of the clear plastic by placing the spudger on the roller brush side and pushing the cap outward.

    Editar

  17. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 16, imagem 1 %32 Shark Rotator Powered Lift-Away Speed Roller Brush Replacement: passo 16, imagem 2 %32

    • Remove the belt from the gear.

    Editar

  18. Shark Rotator Powered Lift-Away Speed Roller Brush Replacement, Roller Brush: passo 17, imagem 1 %32

    • Pull roller brush away from the vacuum.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

9 outras pessoas executaram este guia.

Autor(a)

com 1 outro contribuidor

Sujey Ruano

Membro desde: 10/08/18

706 Reputação

Autoria de 3 guias

Emblemas: 12

+9 outros emblemas

Equipe

Cal Poly, Team S4-G6, White Fall 2018 Membro de Cal Poly, Team S4-G6, White Fall 2018

CPSU-WHITE-F18S4G6

Membros da 4

Autoria de 12 guias

12 comentários

By God, what an ordeal: the excruciatingly hard to find screw behind the roller brush was a phillips on my machine. Thanks a google, nw.

Nicholas - Responder

Exactly, I struggled for sometime trying to find that 1 little screw that was a Phillips head.

Autumn Lamoon Creech - Responder

I figured out how to get it apart… Where do I find a new roller?

Scott D Selk - Responder

where can i get a new roller also...

STEVE BOSCH -

We will never, ever buy a Shark vacuum again. What a nightmare

HOG Rider - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 49

Últimos 7 dias: 361

Últimos 30 dias: 1,687

Duração total: 36,256